VF 11/TD 04.question
Moderators: Helpinators, Moderators
-
- Third Gear
- Posts: 709
- Joined: Tue Feb 14, 2012 11:20 am
- Location: Seattle, WA
VF 11/TD 04.question
Can I use my vf 11 oil and coolant lines on the td04 turbo?
93ss 3inch tbe, Hallman mbc,06 wrx td04, tmic, bov, bugeye seatsStolen x2, sold
93ss Stroker,440cc inj, VF39, '06 TMIC, EJ20G heads & intake, EJ25 crank, 4.11Traded
93ss 4eat, coils, stanced, wraped, flat black, stock show car
93ss Stroker,440cc inj, VF39, '06 TMIC, EJ20G heads & intake, EJ25 crank, 4.11Traded
93ss 4eat, coils, stanced, wraped, flat black, stock show car
-
- Second Gear
- Posts: 322
- Joined: Sat Mar 03, 2007 8:10 am
- Location: arvada co
Re: VF 11/TD 04.question
Yes you can, you'll have to separate the top and lower coolant lines apart from each other since the center section of the turbo are a different spacing between them. Get new crush washers. Oil feed should be the same as the td04.
91 SS, v9 ej207 twin scroll swap, Gda wrx dash swap.
2002 wrx sport wagon
2002 wrx sport wagon
-
- Third Gear
- Posts: 709
- Joined: Tue Feb 14, 2012 11:20 am
- Location: Seattle, WA
Re: VF 11/TD 04.question
How do I know which lines are what? Is there a thread or a link to pictures I can look at? I know there are two lines on top and two on either the side or the bottom. Which lines are what and where can I get crush washers?
93ss 3inch tbe, Hallman mbc,06 wrx td04, tmic, bov, bugeye seatsStolen x2, sold
93ss Stroker,440cc inj, VF39, '06 TMIC, EJ20G heads & intake, EJ25 crank, 4.11Traded
93ss 4eat, coils, stanced, wraped, flat black, stock show car
93ss Stroker,440cc inj, VF39, '06 TMIC, EJ20G heads & intake, EJ25 crank, 4.11Traded
93ss 4eat, coils, stanced, wraped, flat black, stock show car
Re: VF 11/TD 04.question
The oil feed line to the turbo is the small diameter line that comes from the head. The oil return is the larger pipe on the bottom that goes back into the head.
The coolant lines are on the side of the turbo and as mentioned, there is a tab that connects them. Just cut that tab and you can bolt them right up to the TD04.
I don't know if the TD04 is the same as the TD05, but in order to use the vf11 coolant lines I had to drill out the hole so the larger TD05 banjo bolt could go through. I'm not sure if the TD04 is the same.
The coolant lines are on the side of the turbo and as mentioned, there is a tab that connects them. Just cut that tab and you can bolt them right up to the TD04.
I don't know if the TD04 is the same as the TD05, but in order to use the vf11 coolant lines I had to drill out the hole so the larger TD05 banjo bolt could go through. I'm not sure if the TD04 is the same.
Josh
surrealmirage.com/subaru
1990 Legacy (AWD, 6MT, & EJ22T Swap)
2020 Outback Limted XT
If you need to get a hold of me please email me rather then pm
surrealmirage.com/subaru
1990 Legacy (AWD, 6MT, & EJ22T Swap)
2020 Outback Limted XT
If you need to get a hold of me please email me rather then pm
-
- Third Gear
- Posts: 709
- Joined: Tue Feb 14, 2012 11:20 am
- Location: Seattle, WA
Re: VF 11/TD 04.question
If I bought a a full set of the lines would that be easier? The turbo as it sits has no fittings coming from in between the front and exhaust halves.
93ss 3inch tbe, Hallman mbc,06 wrx td04, tmic, bov, bugeye seatsStolen x2, sold
93ss Stroker,440cc inj, VF39, '06 TMIC, EJ20G heads & intake, EJ25 crank, 4.11Traded
93ss 4eat, coils, stanced, wraped, flat black, stock show car
93ss Stroker,440cc inj, VF39, '06 TMIC, EJ20G heads & intake, EJ25 crank, 4.11Traded
93ss 4eat, coils, stanced, wraped, flat black, stock show car
Re: VF 11/TD 04.question
You will use all your old vf11 lines.
Josh
surrealmirage.com/subaru
1990 Legacy (AWD, 6MT, & EJ22T Swap)
2020 Outback Limted XT
If you need to get a hold of me please email me rather then pm
surrealmirage.com/subaru
1990 Legacy (AWD, 6MT, & EJ22T Swap)
2020 Outback Limted XT
If you need to get a hold of me please email me rather then pm