legacycentral bbs

Thanks guys, I just hope my idea of the remote reservoir works! I know it would be ok if it was a gravity feed system, but I don't know if the pump will create enough suction to pull it from below. I was thinking that as long as it is primed, it should be OK... Just not sure until we try it.

Here is a link with more information about the modified power steering pump..
http://bbs.legacycentral.org/viewtopic. ... 801#290801

Here is a little DIY that I just did in order to save a few bucks on a new pump. We were thinking about getting a WRX pump to clear our under manifold turbo inlet, but why not just make the stocker work?? Stock pump right off of the car. http://photos-f.ak.fbcdn.net/hphotos-ak-snc1/hs004.snc1/2795_7...

PICTURES!! WRX struts/springs are in, and the 205-55-16 Maxsport Rally Tyres are ON! http://photos-h.ak.fbcdn.net/hphotos-ak-snc1/hs004.snc1/2795_79134313183_500753183_1679471_3250269_n.jpg http://photos-a.ak.fbcdn.net/hphotos-ak-snc1/hs004.snc1/2795_79134873183_500753183_1679480_7110322_n.jpg Coola...

Been lazy with the camera lately, but we have actually got a good amount done. Got the transmission tunnel all seam welded up along with some other seams under the car. After we did that, we undercoated it with G.G.U by Winzer (Grit Gravel Underbody paint).. Then we were almost ready to install the ...

Might be willing to part with ours... I will let you know.

Made some more progress today! Got the intake manifold off of the motor, along with the power steering pump. Removed the wiring harness and fuel lines from the manifold. Test fit the pass-through turbo inlet and figured out what all needed to be trimmed. Cut off 3 tabs off of the manifold to make ro...

I think the decision has been made to change up our intake (pre turbo) idea. Since these cars did not come equipped with a under the manifold inlet pipe, many get a 90deg silicone elbow and put it right on the turbo and plumb there intake that way. We tried this method, and are not happy with it! We...

PM's sent

Bump for a updated first post!

Update Time!! Started to gut this thing over the weekend! Before: http://farm4.static.flickr.com/3570/3458183408_3903ef4b50_b.jpg http://farm4.static.flickr.com/3533/3457366295_fab29a6061_b.jpg http://farm4.static.flickr.com/3492/3458186152_9f07a094ff_b.jpg After: http://farm4.static.flickr.com/3660...

Found this site while looking for some old school Colin McRae Legacy pictures. Pretty cool if you want to mess around with design ideas. http://carblueprints.narod.ru/subaru.htm http://car-blueprints.narod.ru/images/subaru/subaru-legacy-rs-1991.gif http://car-blueprints.narod.ru/images/subaru/subaru...

We got some parts in finally! Our 2.25"-3" 90deg elbow from siliconeintakes.com showed up. Also we got our silicone Y-Pipe for the intercooler and throttle body coupler! Wiring harness has been moved around some to make room for the Y-pipe, along with the PCV system. This thing is ALMOST r...

Bump this up! I hope to have the complete interior out of this thing this weekend!

Damn... Wish I could pull the trigger on the PP6.

The rear section of the center console and seat belt trim is SOLD!!

What part of the center console do you want? The main section? or all 3 pieces? Mainly the storage compartment part (between the seats). This is what I took out for you. Shoot me an offer if you see something you like! http://farm4.static.flickr.com/3638/3428093250_53d2c3ca25_b.jpg The rear section...

wfoote wrote:do you have the power antenna, and if so how much? What I am really after is the mounting bracket.

Yes. I will try to get it out tomorrow.

As for price, IDK. I have no idea how much any of these old used parts are worth. Just make me a reasonable offer and we will go from there.

HeliCoil exhaust manifold studs- DONE! http://farm4.static.flickr.com/3399/3427281387_d43e20d68e_b.jpg Manifolds, crossover and motor mounts- DONE!! http://farm4.static.flickr.com/3356/3427282289_6e8466ca12_b.jpg ABS Delete- DONE! http://farm4.static.flickr.com/3363/3427284143_2f606d8d2a_b.jpg http:...

Fkyx wrote:How about the trunk pull lever and the center console?

Are you keeping the vent covers in the dash?

What part of the center console do you want? The main section? or all 3 pieces?

The center console is up for grabs. I can get it out and take pictures of it tonight or tomorrow.

The trunk pull lever has the plastic piece missing which I am assuming is what you are after.

The dash we are going to keep intact for the most part.

dropdfocus wrote:The guys on DirtyImpreza are watching this build HARD!!!

You know how I roll!

I really dig your intake setup!

Also nice to see a Leg with no cancer.

We have a 91' SS that we are gutting, so we have many parts laying around that we do not need! The entire interior will be removed from the vehicle so if you need any interior trim pieces let me know! The dash will be staying in the car, but other then that I am pretty sure everything else is coming...

I want to welcome aboard our newest sponsor, Team Illuminata!! WOOT!!! We have not had to much time lately to really work on this thing. This week we plan on really getting to work on it. We would really like to get it ready for the first RallyX race on the 19th of this month. So a week and a few da...