Search found 197 matches

by martimus919
Tue Sep 11, 2018 6:19 am
Forum: Electrical
Topic: Burning up MAF's
Replies: 17
Views: 3579

Re: Burning up MAF's

Legacy777 wrote:I have a similar 90 amp HO alternator and it's fine. Have you checked the voltage? If so, what is it outputting?
Last I remember I have 14v at the battery and am also reading on the dash.
by martimus919
Sat Sep 08, 2018 8:34 pm
Forum: Electrical
Topic: Burning up MAF's
Replies: 17
Views: 3579

Re: Burning up MAF's

I went ahead and made a new harness and replaced the old one. Car started right up and has been running pretty well. I still need to wire in the VSS wire, I keep getting a code for that after a little bit of driving. The other night when I got home from work I did notice the fuel pump had started to...
by martimus919
Thu Jul 26, 2018 6:47 am
Forum: Electrical
Topic: Burning up MAF's
Replies: 17
Views: 3579

Re: Burning up MAF's

If the fuel pressure doesn't hold then I would look at the regulator. Fuel pressure should stay up after the pump is primed. Based on my logs from my Link ECU, fuel pressure was at 43.5 psi with the key in the ON position and engine not running on initial startup. The fuel pump primes like to stock...
by martimus919
Sun Jul 22, 2018 6:57 pm
Forum: Electrical
Topic: Burning up MAF's
Replies: 17
Views: 3579

Re: Burning up MAF's

Are you saying that if you pinch off the line supplying air to the IAC valve the car will idle ok? Does it not idle when you don't pinch off that line? Exactly right. However, it would not drive well. I could make it up my drive way and into the garage in low range but it was a bit of a struggle. S...
by martimus919
Sat Jul 07, 2018 10:07 pm
Forum: Electrical
Topic: Burning up MAF's
Replies: 17
Views: 3579

Re: Burning up MAF's

Well, I made a new discovery today. I found that when I pinch off the IAC the car will idle. Thinking I had a bad IAC I swapped it out to find the same results. I'm wondering If maybe I have bad wiring perhaps. I'm going to test the continuity of the wiring to see if wiring has been damaged.
by martimus919
Tue May 08, 2018 7:00 am
Forum: Electrical
Topic: Burning up MAF's
Replies: 17
Views: 3579

Re: Burning up MAF's

Hmmm, that's interesting about the howling fuel pump. If you've replaced the pump, are you sure it's the fuel pump that is howling? Oh yeah, it is quite clear where the noise is coming from. Once I put the upgraded fuel pump in it's hard to not notice anything else. I replaced the fuel pump thinkin...
by martimus919
Sat May 05, 2018 6:41 pm
Forum: Electrical
Topic: Burning up MAF's
Replies: 17
Views: 3579

Re: Burning up MAF's

Are you still having issues with MAF's? Yes, I haven't really done anything with it over the winter. But one thing that I did not mention before that I think may be related is that my fuel pump howls, sometimes it goes away. But I thought it was the factory pump so I upgraded to a Deatschwerks pump...
by martimus919
Mon Jan 29, 2018 12:44 am
Forum: Electrical
Topic: Burning up MAF's
Replies: 17
Views: 3579

Re: Burning up MAF's

you've checked the Voltage @ the MAF wiring? Probably could use a resistor (?) to lower to the 5V or whatever it should be. What does Wiring Trim mean? Merged harness? I get battery voltage at the MAF sensor and have 5v at pin 5, and I also have a good ground. As far as the harness trim, I simply t...
by martimus919
Mon Nov 27, 2017 7:18 am
Forum: Electrical
Topic: Burning up MAF's
Replies: 17
Views: 3579

Burning up MAF's

I'm getting pretty burnt out working on this car of mine. I've swapped an EJ22t into my 90 Loyale and have been having an issue burning up MAF sensors. It seems to be getting worse, and I'm running out of sensors. I'm guessing it's in the wiring trim I did, like not enough grounds or something but I...
by martimus919
Mon Nov 21, 2016 8:01 am
Forum: Car Lot
Topic: Nevada - SOLD: 91SS 5MT Robtune.
Replies: 10
Views: 3851

Re: FS: 91SS 5MT Robtune 22T daily - rust free Nevada

A couple guys keep asking me for mine at work. I'll let them know about yours, I think I still have your number so I'll try to text you within the next couple of days if they're interested.
by martimus919
Mon Nov 21, 2016 8:00 am
Forum: Car Lot
Topic: Nevada - SOLD: 91SS 5MT Robtune.
Replies: 10
Views: 3851

Re: FS: 91SS 5MT Robtune 22T daily - rust free Nevada

A couple guys keep asking me for mine at work. I'll let them know about yours, I think I still have your number so I'll try to text you within the next couple of days if they're interested.
by martimus919
Wed Aug 31, 2016 3:16 am
Forum: Parts Shed
Topic: Rebuilt MHI TD05H 16g Billet 90 degree inlet
Replies: 8
Views: 1651

Re: Rebuilt MHI TD05H 16g Billet 90 degree inlet

Does it come with the wastegate actuator?
by martimus919
Sun Jul 17, 2016 5:36 am
Forum: Turbo
Topic: "Best" Turbo for a 550 Robtune
Replies: 10
Views: 3721

Re: "Best" Turbo for a 550 Robtune

I'm running a 550 tube and a VF23 on a 22t with 20g heads, spools real fast and carries well to 7k
by martimus919
Wed Mar 23, 2016 6:05 pm
Forum: Electrical
Topic: What is revtronix
Replies: 3
Views: 1180

Re: What is revtronix

I couldn't agree more with Mike. I've been so much happier with my RobTune than I ever was with my Revtronix.
by martimus919
Sat Dec 19, 2015 9:24 am
Forum: Drivetrain
Topic: using a SVX transmission in 93 TLeg Wagon
Replies: 4
Views: 1244

Re: using a SVX transmission in 93 TLeg Wagon

I swapped a 97 Outback 4.44 trans and diff into my father in laws 94 SVX after his stock one started to go. It drove considerably better with the lower gearing. As stated before the taller gears cause heat problems which in turn take out the trans. Subaru geared them higher to increase highway milea...
by martimus919
Wed Jul 15, 2015 12:42 am
Forum: Parts Shed
Topic: FS Reno: Garage cleanout! EJ22T, parts bonanza, etc.
Replies: 9
Views: 1280

Re: FS Reno: Garage cleanout! EJ22T, parts bonanza, etc.

I've noticed no one has called dibs yet on it, soooo..... Dibs!
by martimus919
Tue Jul 14, 2015 8:35 pm
Forum: Parts Shed
Topic: FS Reno: Garage cleanout! EJ22T, parts bonanza, etc.
Replies: 9
Views: 1280

Re: FS Reno: Garage cleanout! EJ22T, parts bonanza, etc.

I'm also interested in the LSD if the other sale fall through. Located in north Reno.
by martimus919
Fri Jul 10, 2015 7:07 am
Forum: Wheels, Tires and Brakes
Topic: Kartboy VS. KNS rear brake adapters
Replies: 12
Views: 4090

Re: Kartboy VS. KNS rear brake adapters

Josh,

They're made out of mild steel, and I went with high grade bolts for added peace of mind.

Let me know when you want a set.
by martimus919
Tue Jun 30, 2015 2:50 pm
Forum: Wheels, Tires and Brakes
Topic: Kartboy VS. KNS rear brake adapters
Replies: 12
Views: 4090

Re: Kartboy VS. KNS rear brake adapters

I should have 13 left.
by martimus919
Tue Jun 30, 2015 6:53 am
Forum: Wheels, Tires and Brakes
Topic: Kartboy VS. KNS rear brake adapters
Replies: 12
Views: 4090

Re: Kartboy VS. KNS rear brake adapters

I have adapters I made for $100 shipped no drilling required. I've been running them for a few years now with out problems.

Image

Haven't test fit my Brembos with rotors yet, but should work with Brembos also.
by martimus919
Sat Jun 06, 2015 9:51 am
Forum: Body, Chassis and Interior
Topic: Revlimiter custom gauges
Replies: 18
Views: 4931

Re: Revlimiter custom gauges

I would love some nice black and white gauges with a higher red zone. Eager to hear if he's willing to do some stuff for us weirdos and our Legacys.
by martimus919
Thu May 28, 2015 4:18 am
Forum: Engine
Topic: EJ22T VS. EJ20G
Replies: 7
Views: 1364

Re: EJ22T VS. EJ20G

Did you ever try a built 22k engine? That's what I was going for. That's why I have the K engine now. Going to start building a stroker 2.2 with the K heads so I can get rid of the hydro heads and have a 9g reving engine. My G heads are ported and polished, so of course I have to do it to the K hea...
by martimus919
Wed May 27, 2015 8:38 pm
Forum: Engine
Topic: EJ22T VS. EJ20G
Replies: 7
Views: 1364

Re: EJ22T VS. EJ20G

I've ran a built 2.2 w/ 20g heads and a Stock 20k engine with a RobTune, and the 20k was only fun in high rpms. I would rather have a stock 2.2 than a 20g/k to be honest. Real fast spool, non interference engine and still able to make plenty of power to have a lot of fun.
by martimus919
Fri Apr 03, 2015 6:28 am
Forum: Car Lot
Topic: looking for first gen sedans
Replies: 5
Views: 1337

Re: looking for first gen sedans

Airport Auto Wrecking in Reno has a 93 N/A manual with minor fender damage. The car has around 65k on it, really clean car.
by martimus919
Wed Dec 17, 2014 7:38 am
Forum: Engine
Topic: Bucking and hesitation issues
Replies: 27
Views: 2826

Re: Bucking and hesitation issues

I'd say I might have a spare ECU if you're driving through Reno but mine does something similar, mostly doesn't do anything exciting under boost and occasionally bucks on me. I've learned to work the clutch to limit the bucking. Figured I'd look into it again if it did it after the new engine's put ...