legacycentral bbs

Still looking? How much can you offer? Where are you?

I need to check if my friend's car hauler is available. No hubs so wheels cannot be attached correct?

Is the rear spoiler still available? How much shipped to 33186?

bmxpunk wrote:I am selling my 20g ecu with the ESL board if anyone is interested.

How much?

Also, could I just as easily go with a modern N/A transmission, or does the fact that a transmission comes from a turbo car make that much of a difference? Which came with hydraulic clutch? Finally, if I do finally retrofit a newer trans, how hard is the switch from push style to pull style clutch? ...

Does anybody know for sure if the following information is accurate? 1990-1991 Legacy MT 1st: 3.545 2nd: 1.947 3rd: 1.366 4th: 0.972 5th: 0.738 Rev: 3.416 FWD: 3.700 AWD: 4.111 Turbo: 3.900 (Note: Turbo model was only available in the 1991 MY) AT 1st: 2.785 2nd: 1.545 3rd: 1.000 4th: 0.694 Rev: 2.27...

I have a 1993 Subaru Legacy Sport Sedan Assuming the factory transmission. What's easier? Cheaper? Stronger? I will research costs, but want to understand my options. This is to be done on a tight budget, so I'm looking for easiest way to get the strongest possible factory 5MT in there or rebuild or...

How about now? Still there?

Still available?

Still available? Any pics or details?

Add me to list for Post Facelift lights and corners. I have a USDM post facelift model, so I guess I'd need the corners to go along with the headlights.

I can't wait to put them to good use. 17x8's with a 48mm offset should clear I imagine.

I had to edit it after I looked them up.

Actually, I forgot to mention in my original post that the front rotors are the bigger diameter 316 x 30 mm thick rotors from the 2005 + Legacy GT as opposed to the 294 x 24 or 295 x 25.5 front rotor from the WRX. That's why I felt that I needed to shift some of the brake bias to the back with dissi...

http://i1198.photobucket.com/albums/aa4 ... b2c794.jpg

http://i1198.photobucket.com/albums/aa4 ... 1418869526

My favorite pics so far.

Josh, I'd love to hear your take on the setup that's going on my car, since you put up all that brake math in the past. I've got the whole Nissan 300ZX setup for the front and rear. I'm using the front caliper brackets from KNS and the rear caliper brackets from Godspeed. The rotors are stock style ...

This is the sort of porting I'm talking about.

https://encrypted-tbn2.gstatic.com/imag ... skUC-mNNIw

Anybody else? Anybody with experience having a comparable turbo with and without anti-surge?

From what I understand, the anti-surge porting allows excess pressure in the compressor side that cannot be used by the engine, or cannot flow past a more restrictive exhaust housing to flow back into the intake tract rather than stall the compressor wheel. It sounds to me like it would allow the tu...

Could anti-surge be of any use with the turbos typically used in our Legacys? Should I end that with an ies, instead of a ys? Questions to ponder. But seriously if I was installing a VF22 compressor / VF34 turbine hybrid, billet aluminum compressor wheel with extended tips, and ceramic coating on ex...

How did you get Nissan 4 pot fronts and 2 pot rears for $200.00 in rebuilt condition? I paid $225.00 for front and rear total, but they need to be rebuilt. The rears were nicely powdercoated though. I did not get the Aluminum front calipers. Mine are iron. Also, I'm sure plenty of people would be in...

Possum link G1 ECU. As in Possum Bourne? Never heard of it. I'm intrigued. Beautiful car. We're glad you joined.

Actually, Josh is this the same ECU you have?

You would use the same principal as Electric Power Steering except pumping water into a chamber. You would adjust the static LPH rate and the progressive gain based on wheel position to get the right balance. Of course, going opposite lock would then cause it to go the "wrong" direction ag...

Can't I simply bypass it, drive it home, then replace the reservoir with a good original? Of course I would buy one from one of you fine people. Yes, the turbo would be strictly oil cooled in the meantime. That's OK. I wouldn't be abusing it, and I'd let it idle to cool down before I shut it off. I'...

http://www.killerbmotorsport.com/index_ ... e21151.jpg

Could I possibly use this piece to replace my factory one?

Can a 2002 - 2007 WRX or STI part be used to replace this, even if temporarily?