legacycentral bbs

Part number referrence needed
Page 3 of 5

Author:  123c [ Thu Jun 03, 2004 3:55 pm ]
Post subject: 

Legacy777 wrote:
It's called the abs ring. I could look it up when I get home. What year, model, etc car do you have?

1993 Legacy SS

Tone Wheel Front: 26750AA003

Author:  123c [ Wed Jun 09, 2004 9:07 pm ]
Post subject: 

New part number needed, I can't seem to find, even in that nice parts reference book Josh provided, and Subaruparts.com can be a little confusing at times.

I can't seem to find the number for the little rubber boots that go over the slide pins on the brake calipers, one of them has a small tear, so I figure I should replace it, and probally all of them...

Author:  Legacy777 [ Thu Jun 10, 2004 1:13 am ]
Post subject: 

You can't buy just the boot, however you can buy a rebuild kit that has the boots, seals and lube

Depending on when your car was made....there's two different #'s

If it was made on or before sept of 92 the # is

If it was made on or after oct of 92 the # is 26297AA021

Author:  123c [ Thu Jun 10, 2004 5:11 pm ]
Post subject: 

Do the rebuild kits also come with the anti-rattle clips?

Author:  Legacy777 [ Thu Jun 10, 2004 6:12 pm ]
Post subject: 

no.....just the parts to rebuild the caliper

Author:  123c [ Sun Jun 13, 2004 2:14 am ]
Post subject: 

Ok, here's another part I can't seem to find, I am looking for the bushings that go into the Stabilizer Link Assembly. I can't seem to find it, I can only find the Stabilizer Link Assembly, but no bushings for it.

Author:  eastbaysubaru [ Wed Jun 16, 2004 11:54 pm ]
Post subject: 

I hope this is an easy one. I've got a few Grill Clips that are broken. The lower middle clip and the clip attached to the passenger side headlight are both broken. Does anyone have the part number for these clips? TIA.


Author:  123c [ Thu Jun 17, 2004 12:46 am ]
Post subject: 

outer clips: 91017AA010
inner clips: 91059FC090

Author:  eastbaysubaru [ Thu Jun 17, 2004 5:17 am ]
Post subject: 

Which is which? I need one of the ones that attaches to the headlight (outer?) and one that attaches in the center on the bottom (inner?). Outer and Inner seem like they refer to the top clips as there are four of them. The ones that I need are the ones that the grill slides down onto.


Author:  eastbaysubaru [ Thu Jun 17, 2004 10:10 pm ]
Post subject: 

Front wheel bearing:


Seals for associated bearings:

28015aa070 (inner?) not sure which is which
28015aa021 (outer?)


Author:  vrg3 [ Thu Jun 17, 2004 10:25 pm ]
Post subject: 

The front wheel bearing should be part number 28016AA011. The inner seal is part number 28015AA021 and the outer seal is part number 28015AA070.

I think you need a snap ring for one or both seals; the snap ring is part number 28035AA010.

Author:  eastbaysubaru [ Fri Jun 18, 2004 5:01 am ]
Post subject: 

Thanks for the extremely helpful reply Vikash. The part number for the wheel bearing has been superceded by the part number I listed:



Author:  vrg3 [ Fri Jun 18, 2004 2:26 pm ]
Post subject: 


I didn't see that you had edited your post. (That's what happened, right?)

An odd thing I noticed -- the GD-chassis WRX/RS has the same part numbers except for the inner seal which is part number 28015AA080. I would have expected it to be the same.

Author:  eastbaysubaru [ Fri Jun 18, 2004 3:55 pm ]
Post subject: 

Yeah, I edited it as I was calling the local Oakland dealership. They were actually pretty helpful this time and gave me all the associated part numbers that I needed. They didn't tell me about the snap rings though, so thanks!


Author:  123c [ Fri Jun 18, 2004 11:07 pm ]
Post subject: 

As far as I know, there are no snap rings. I just had my bearing pressed last week, and the machine shop didn't say anything about one...

Author:  ferre [ Mon Jan 24, 2005 7:18 am ]
Post subject: 

hi all :)

i'm wondering if anyone would know where i could get the part number for a JDM 2lt gt legacy auto ECU

or even better would be if anyone knows of a parts list for JDM legacy's
i noticed a similar question posted earlier in this thread but it was from awhile ago so i though i would ask in case there is any upadtes

Author:  Legacy777 [ Mon Jan 24, 2005 4:10 pm ]
Post subject: 

Hmm....I don't have any JDM part #'s

There might be someone else.

Have you tried www.rslibertyclub.org/forums ?

Author:  THAWA [ Wed Apr 20, 2005 7:30 am ]
Post subject: 

Does anyone know the part number for the v8+/USDM STi, Legacy GT/Outback XT, Legacy 2.0GT oil pan. The twin scroll one?

Author:  Legacy777 [ Wed Apr 20, 2005 5:41 pm ]
Post subject: 

is it different?

Author:  THAWA [ Wed Apr 20, 2005 8:38 pm ]
Post subject: 


Author:  Legacy777 [ Wed Apr 20, 2005 11:57 pm ]
Post subject: 

how so? and what if any are the benefits....or is it just a fitment issue?

Author:  THAWA [ Thu Apr 21, 2005 1:04 am ]
Post subject: 

It is shaped to allow the use of twinscroll headers.

Author:  dzx [ Thu Apr 21, 2005 2:23 am ]
Post subject: 

I remember hearing about twinscroll turbos but i dont remember what subaru's they come on. I do remember that there are quite a few differences in the setup.

Author:  THAWA [ Thu Apr 21, 2005 2:30 am ]
Post subject: 

They come on v8+ STi's and Legacy 2.0GT's :)

Author:  Legacy777 [ Thu Apr 21, 2005 3:17 am ]
Post subject: 

None that came in the USA correct?

Page 3 of 5 All times are UTC [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group