ej22 na turbo help pls

That spinning thing that makes all of the cool noises. OE and Aftermarket.

Moderators: Helpinators, Moderators

Legacy777
Site Admin
Site Admin
Posts: 27884
Joined: Tue Oct 15, 2002 11:37 am
Location: Houston, Tx
Contact:

Re: ej22 na turbo help pls

Post by Legacy777 »

Ok, good to know.
Josh

surrealmirage.com/subaru
1990 Legacy (AWD, 6MT, & EJ22T Swap)
2020 Outback Limted XT

If you need to get a hold of me please email me rather then pm
bcmaxx
First Gear
Posts: 218
Joined: Wed Oct 24, 2012 6:30 pm

Re: ej22 na turbo help pls

Post by bcmaxx »

Looking for a bit more fuel. At 16psi its a bit lean at 12,3 ish when im hard on the gas. Rrfpr is maxxed. Can i do anything to the stock injectors or swap in my ej22t injectors and rails ? Im on the smallest water injection nozzle. Upping one size help?
Legacy777
Site Admin
Site Admin
Posts: 27884
Joined: Tue Oct 15, 2002 11:37 am
Location: Houston, Tx
Contact:

Re: ej22 na turbo help pls

Post by Legacy777 »

You wouldn't really be able to swap injectors since the ECU is matched with the injectors and swapping in a turbo Legacy ECU isn't going to work either.

Do you have a higher flow fuel pump? You could try a different RRFPR with an increased rising rate.
Josh

surrealmirage.com/subaru
1990 Legacy (AWD, 6MT, & EJ22T Swap)
2020 Outback Limted XT

If you need to get a hold of me please email me rather then pm
bcmaxx
First Gear
Posts: 218
Joined: Wed Oct 24, 2012 6:30 pm

Re: ej22 na turbo help pls

Post by bcmaxx »

Ive decided to run lower boost until i get the turbo block finished and in. It will likely have different fuel demands with a lower cr. Currently running a holly variable rrfpr and meth injection
bcmaxx
First Gear
Posts: 218
Joined: Wed Oct 24, 2012 6:30 pm

Re: ej22 na turbo help pls

Post by bcmaxx »

Fixed! It was suggested I clean my maf, cleaned, and now I have all the fuel i need.
bcmaxx
First Gear
Posts: 218
Joined: Wed Oct 24, 2012 6:30 pm

Re: ej22 na turbo help pls

Post by bcmaxx »

Another odd question. I need to replace my turbo oil feed line. My bastards tee fitting off the oil press sensor location is leaking a bit. What is recommended size? Im using 1/4 inch tubing at the moment.
cj91legss
Fifth Gear
Posts: 6322
Joined: Fri Jun 20, 2008 8:17 am
Location: Lakewood, Wa 98439
Contact:

Re: ej22 na turbo help pls

Post by cj91legss »

The first post of this thread http://sl-i.net/FORUM/viewtopic.php?f=39&t=22065 shows you a good option for an oil feed line for the factory non turbo setup.

Might be something to try?
91 L-TW Wagon with a full Swap -RIP
92 SS Prefaced, GD dash swapped, 22T/205 Hybrid 20 psi - BEAST!
93 SS Bone Stock Gone!
94 TW Bone Stock Gone!
91 SS 4EAT Sold!
98 LGT 4EAT
98 LGT Wagon 4EAT
bcmaxx
First Gear
Posts: 218
Joined: Wed Oct 24, 2012 6:30 pm

Re: ej22 na turbo help pls

Post by bcmaxx »

Thanks! I found another on there too http://www.ebay.ca/itm/MK1-Turbo-Oil-Fe ... RTM1963930

but not sure if it will work?
Post Reply