PNW: legacy dyno day!!! TIME AND DATE IS OFFICIAL!!!

[Thesubielover]

What year was that stock STI when it was dynoing?

[Thesubielover]

How many people do you have coming so far? We should also try to get a group together to go down to high school drags (even though most of us are not in high school) at pacific raceways in may.

[euroshark]

04 sti

[kimokalihi]

Pretty sure I'm not going now. Got transfered to dayshift and I still work weekends so I'll be at work.

[euroshark]

damn, i was hoping to see your whip in person

[Thesubielover]

I saw it a couple weeks ago, and its pretty clean.

[kimokalihi]

Yeah sucks. Seems like either shift sucks. Day shift starts between 10am and 2pm. During the week ill get off at 8-10 and on fri and sat ill get off at 10-midnight. Stupid hours. But on nights I work 8pm-4am so that sucks too. Damn casino.

[euroshark]

official date and time has been set. saturday may 5th at 9am. be there!!!

[Alphius]

Are we meeting at the shop at 9AM? Address? I will try to come but short notice might have me missing this one. Good job on the meet!

[kimokalihi]

Gonna be at the sand dunes in oregon. Njoi guise!

[mike-tracy]

Was hoping to go but that's the weekend of the Oregon Trail rally that kleinkid and I are volunteering at.

[ciper]

I just did mine but they didn't have an rpm clamp for obd1 cars

What the hell? Why not use an inductive signal from spark plug wire (high voltage) or a trigger wire to the coil? I had trouble with a smog test once so we peeled back the rubber cover on the wires to the coil and used that to get a stable rpm signal.

[kimokalihi]

These guys were rookies with the dyno. They've only had it maybe a year and had never done an AWD car before. It was actually pretty gut wrenching to watch at first because they didn't know how to release the front rollers and kept trying to take off with them locked and only the rear wheels were spinning. I was not even allowed in the shop while they were doing the runs so I had to sit behind the windows softly crying by myself. They came in and asked me if I was sure my car was AWD and not RWD...I told them they must have the front rollers locked but they couldn't figure out how to unlock them for a while.

[kimokalihi]

It's come to my attention that what I said above may sound like I'm talking about this shop but that all took place at SPSCC. I've never been to this shop before.

[Thesubielover]

I'll be there. Hoping to get my gauge's and boost controller on in time! We should get drinks or dinner, or something after

[euroshark]

alphius, this will be at the shop. the address can be found in the link in my sig.

sorry most of you guys cant make it, i was hoping to meet a lot of you in person.

robert, i would love to get dinner but i have to watch my daughter that night so i will be leaving the shop around 4.

[Thesubielover]

euroshark, when are you getting there? I'll probably get there a little early so I can get a good spot. Are you off sometime before saturday and be interested in getting together?

[euroshark]

i will be there very early so i can set everything up.

[originalcyn]

Maybe i'm missing something, is it going to be hard to find a spot? I mean, if I come at 12 or something are people still going to be there?

[vica153]

Parking up close might be a bit limited with all the project cars there, but there is plenty of street parking out front and within the surrounding block.

[euroshark]

well... its the morning of the event, hope to see most of you there.

[Alphius]

Can't make it. Maybe next time.

[kimokalihi]

226 whp

[vica153]

^That Rob tune did an impressive job.

[BSOD2600]

Can't make it. Maybe next time.

Shame. Was hoping to finally find out what it was makin' after all these years.