EJ22t Short Block/EJ205 Heads, Who done it

Heads, valves, pistons, rods, crankshaft, etc...

Moderators: Helpinators, Moderators

cj91legss
Fifth Gear
Posts: 6322
Joined: Fri Jun 20, 2008 8:17 am
Location: Lakewood, Wa 98439
Contact:

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by cj91legss »

thatscarycat wrote:I had that 90* PCV removed and capped off on my block.
I left mine and tapped holes inn my valve covers to stil have the vents like it is on the STI and turbo legacy.
91 L-TW Wagon with a full Swap -RIP
92 SS Prefaced, GD dash swapped, 22T/205 Hybrid 20 psi - BEAST!
93 SS Bone Stock Gone!
94 TW Bone Stock Gone!
91 SS 4EAT Sold!
98 LGT 4EAT
98 LGT Wagon 4EAT
Legacy777
Site Admin
Site Admin
Posts: 27884
Joined: Tue Oct 15, 2002 11:37 am
Location: Houston, Tx
Contact:

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by Legacy777 »

cj91legss wrote:I left the sensor for the gauge in the cross over and threaded the newer 3 wire in where the older cts went.
Ok, so you still had the single wire for the dash.
Josh

surrealmirage.com/subaru
1990 Legacy (AWD, 6MT, & EJ22T Swap)
2020 Outback Limted XT

If you need to get a hold of me please email me rather then pm
cj91legss
Fifth Gear
Posts: 6322
Joined: Fri Jun 20, 2008 8:17 am
Location: Lakewood, Wa 98439
Contact:

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by cj91legss »

Legacy777 wrote:
cj91legss wrote:I left the sensor for the gauge in the cross over and threaded the newer 3 wire in where the older cts went.
Ok, so you still had the single wire for the dash.
No. The wrx sensor is 3 wire, 2 for the ecu and 1 for the gauge cluster. Remember I switched everything out. Dash, Harness, ECU, the whole nine yards.

edit...

yes the old dash sensor is still there in the cross over, it took me a second to take in what you typed Josh.
91 L-TW Wagon with a full Swap -RIP
92 SS Prefaced, GD dash swapped, 22T/205 Hybrid 20 psi - BEAST!
93 SS Bone Stock Gone!
94 TW Bone Stock Gone!
91 SS 4EAT Sold!
98 LGT 4EAT
98 LGT Wagon 4EAT
monkeyposeur
First Gear
Posts: 227
Joined: Mon Feb 20, 2012 5:44 pm
Location: Salt Lake City, UT

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by monkeyposeur »

mike-tracy wrote:Also, what are you going to do about the forward PCV? 90* port on the top of the 22t block? I mocked up the ej205/255/7 crossover pipe on my block and it contacts that pipe. My idea is to use a phase I crossover pipe with the sensors on the same side as the ej205's so the wiring easily reaches and cap the port off.
07 Sti crossover pipe clears the PCV 90*. I ran into this issue with my hybrid build. (pic courtesy Fuji K)

Image
Image


I asked a lot of people about the 90* issue (NICO, Fuji K...) and in the end I ended up plugging the hole with a 12.2mm freeze plug at NAPA (part no. 381-3193). It was about $1.30 or something. I used green loctite and tapped it in. Over 5k on the build and no issues whatsoever. Ideally I would have tapped the hole and plugged it with a bolt but I had already assembled the shortblock and didn't want any chance of metal shavings getting in the system. I thought about rigging up a vacuum attachment up against the hole from the oil pan area but the freeze plug works great.

Image
93 SS - SOLD
03 WRX 22T/205 20GXT 350 whp
06 OBXT
95 BK - Sold to my neighbor.
cj91legss
Fifth Gear
Posts: 6322
Joined: Fri Jun 20, 2008 8:17 am
Location: Lakewood, Wa 98439
Contact:

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by cj91legss »

That's another way to do it!
91 L-TW Wagon with a full Swap -RIP
92 SS Prefaced, GD dash swapped, 22T/205 Hybrid 20 psi - BEAST!
93 SS Bone Stock Gone!
94 TW Bone Stock Gone!
91 SS 4EAT Sold!
98 LGT 4EAT
98 LGT Wagon 4EAT
Sinix3
In Neutral
Posts: 31
Joined: Fri Jul 31, 2015 3:38 am
Location: lower mainland bc

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by Sinix3 »

i have a question for you guys. i have a set of sf5 20g heads shim over bucket and i picked up a 22t legacy last night. could i run the 20g heads or would that bump my compression through the roof?
91 legacy wagon 22 na
93 legacy wagon eg33 swap under way
86BRATMAN
Second Gear
Posts: 415
Joined: Sun Mar 04, 2007 4:59 am
Location: Tazewell VA

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by 86BRATMAN »

With stock thickness head gaskets you're looking at about 7.7:1 compression. Those heads are almost identical to 97-99 25d, the only parts that differ are the camshafts and provisions for the turbo oil drain and feed, and turbo coolant feed hose.
Sinix3
In Neutral
Posts: 31
Joined: Fri Jul 31, 2015 3:38 am
Location: lower mainland bc

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by Sinix3 »

Would they be a good choice in heads for a 22t?? I have a set of 96 25d heads as well
91 legacy wagon 22 na
93 legacy wagon eg33 swap under way
86BRATMAN
Second Gear
Posts: 415
Joined: Sun Mar 04, 2007 4:59 am
Location: Tazewell VA

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by 86BRATMAN »

The 96 25d heads are not suitable for use on an ej22 at all. The combustion chambers on them are wider that the bore and will cause hot spots and detonation. The 20g heads you have would be your a good choice for your engine, from many member's reviews even with the low compression ratio off boost drivablility is still very good.
Sinix3
In Neutral
Posts: 31
Joined: Fri Jul 31, 2015 3:38 am
Location: lower mainland bc

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by Sinix3 »

What compression ratio would i end up with?
91 legacy wagon 22 na
93 legacy wagon eg33 swap under way
86BRATMAN
Second Gear
Posts: 415
Joined: Sun Mar 04, 2007 4:59 am
Location: Tazewell VA

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by 86BRATMAN »

86BRATMAN wrote:With stock thickness head gaskets you're looking at about 7.7:1 compression.
Sinix3
In Neutral
Posts: 31
Joined: Fri Jul 31, 2015 3:38 am
Location: lower mainland bc

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by Sinix3 »

to low for a daily at 14 psi?
91 legacy wagon 22 na
93 legacy wagon eg33 swap under way
cj91legss
Fifth Gear
Posts: 6322
Joined: Fri Jun 20, 2008 8:17 am
Location: Lakewood, Wa 98439
Contact:

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by cj91legss »

Not too low at all. Mine is 7.49:1 with the head gaskets I chose.
91 L-TW Wagon with a full Swap -RIP
92 SS Prefaced, GD dash swapped, 22T/205 Hybrid 20 psi - BEAST!
93 SS Bone Stock Gone!
94 TW Bone Stock Gone!
91 SS 4EAT Sold!
98 LGT 4EAT
98 LGT Wagon 4EAT
Sinix3
In Neutral
Posts: 31
Joined: Fri Jul 31, 2015 3:38 am
Location: lower mainland bc

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by Sinix3 »

Well then its definitly the way im going with this build
91 legacy wagon 22 na
93 legacy wagon eg33 swap under way
Aki
First Gear
Posts: 57
Joined: Mon Feb 27, 2012 6:20 pm

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by Aki »

Have done this as well!

02' WRX ECU with the Carberry ROM. EJ20K power steering pump to allow the turbo inlet to clear. Also blocked off that front 90:

Image

Image
cj91legss
Fifth Gear
Posts: 6322
Joined: Fri Jun 20, 2008 8:17 am
Location: Lakewood, Wa 98439
Contact:

Re: EJ22t Short Block/EJ205 Heads, Who done it

Post by cj91legss »

Just curious, not just for myself but for others, what did you do about your speed sensor signal?

Sent from my SM-N920T using Tapatalk
91 L-TW Wagon with a full Swap -RIP
92 SS Prefaced, GD dash swapped, 22T/205 Hybrid 20 psi - BEAST!
93 SS Bone Stock Gone!
94 TW Bone Stock Gone!
91 SS 4EAT Sold!
98 LGT 4EAT
98 LGT Wagon 4EAT
Post Reply