legacycentral bbs

UPDATED: 6/2/2008

My buddy picked up a bunch of motors locally when a local Subaru dealer changed hands & the new owner didn't want all the extra stuff laying around. He moved & needed it all out of his garage now. So I volunteered to sell everything for him.

All parts are located in Williamsport, PA 17701

Here's what is available:
'03 WRX EJ205 short block (50,xxx miles) -
SOLD

'98 LGT EJ25D long block w/ Eagle pistons matching the STi compression specs (73,xxx miles) -
SOLD

'98 LGT EJ25D DOHC heads (68,xxx miles) -
$160 complete

'98 LGT EJ25D short block (68,xxx miles) -
SOLD

Pictures are up now.

Sale pending on the EJ25D short block already...

Added at set of DOHC heads to the list.

bump

The EJ25D short block is sold.

Just an FYI, I have never seen a USDM WRX shortblock sell for more than $300. Those things are given away. Like the Ej25, all the money is in the heads...

I was just going by what the owner of the parts wanted money wise.

Prices have been adjusted accordingly (lowered).

...and the song goes "Bump bump bump"

The 2.5 long block is getting stripped down Thursday to be parted out for quicker sale...

wrx block still available? Is it hurt or in good shape?

WRX block (w/o heads) on hold for a guy in York, PA & Sale Pending for a complete set of heads to smh0101.

WRX block sold.
WRX heads on hold.
EJ25D heads still available.
EJ25D long block w/ low compression pistons still available.

WRX heads sold to Spitfire999 (Ben).
Full set of EJ25D heads (great for Frankenmotor builds)
EJ25D long block w/ low compression pistons still available.

I still want the heads... i'm just going to have to wait for summer paychecks to start rolling in...

You wouldnt mind holding them would you?

Bump up...

Sale pending on the motor.

EJ25D DOHC heads still available.

That longblock sounds nice...

newb question, can I throw anything that isn't on there from my NA EJ22 on?

I might be "in the market", per se, for a small power upgrade...

Yes, you can install EJ25D heads on an EJ22E block. Compression ratio will change a bit & you will have higher flow heads. You also need the matching intake manifold (which I may have a spare to sell, I will have to double check on that) to work with the heads since the 2.2 & 2.5 manifolds are not the same. Also, the exhaust ports are dual port vs. the single that most (not all) 2.2 motors are equiped with.

heads shipped to 06471

dropdfocus wrote:Yes, you can install EJ25D heads on an EJ22E block. Compression ratio will change a bit & you will have higher flow heads. You also need the matching intake manifold (which I may have a spare to sell, I will have to double check on that) to work with the heads since the 2.2 & 2.5 manifolds are not the same. Also, the exhaust ports are dual port vs. the single that most (not all) 2.2 motors are equiped with.

I was actually talking about throwing all the accessories from my EJ22 on the EJ25 longblock, ^^;;;

You'd have a stronger setup if you utilize the 2.2 block & the 2.5 heads. 2.5 motors were/are more prone to over heating and taking out head gaskets. On the other hand, I just regasketed my motor with the SOA dealer head gaskets & it's been just fine.

heads shipped to 06471

28lbs each x 2 packages from 17701 to 06471

UPS Next Day Air Early A.M.®
1 9:00 A.M.
Tuesday
July 1, 2008 198.66 USD*

UPS Next Day Air®
1 10:30 A.M.
Tuesday
July 1, 2008 125.70 USD*

UPS Next Day Air Saver®
1 By End of Day
Tuesday
July 1, 2008 110.84 USD*

UPS 2nd Day Air®
2 By End of Day
Wednesday
July 2, 2008 63.62 USD*

UPS Ground
2 By End of Day
Wednesday
July 2, 2008 25.06 USD*