Page 1 of 1
FS: Random Parts - H6 Rotors, Brake Master Cylinder + more
Posted: Sun Oct 19, 2008 11:02 pm
by mike270
I have a bunch of miscellaneous, random parts just sitting around that someone might be able to get some use out of:
Parts off a 1991 Turbo Legacy with ~167k miles. These are off a stage rally car, but most parts have only seen a few hill climbs under competition.
-- Stock Brake Master Cylinder - $15 – Works great, good condition, no leaks, replaced it when going to my new brake setup. -
Picture
-- Turbo Legacy Donut - FREE
Parts off a 2000 Legacy
-- Stock Front Rotors - $10 - Used, ~23.2mm thickness (22mm minimum as printed on rotor)
-- Stock Rear Rotors - $25 - Used, ~11.4 inch diameter, should have plenty of life left, ~9.6-9.7mm thickness (8.5mm minimum as printed on the rotor) -
Picture
All prices are OBO, so if you are interested, make me an offer!
Posted: Sun Oct 19, 2008 11:44 pm
by skid542
Are the prices for the S/S brake lines including shipping? Truthfully I only need the front, would you be willing to split up? If shipping isn't included, can you give me an estimate to 83835.
I have money in paypal ready.
Posted: Mon Oct 20, 2008 2:36 am
by mike270
PM sent...
Posted: Mon Oct 20, 2008 3:54 am
by wtdash
If the back set of brake lines is avl., please PM shipped to the same place as skid.
Thanks
Posted: Mon Oct 20, 2008 3:56 am
by wtdash
Also, dibs on the Cobb...that's the inline air filter, correct?
Please PM quote w/shipping.
Posted: Mon Oct 20, 2008 4:11 am
by gt2.5turbo
dang i wanted both sets of lines.....
Posted: Mon Oct 20, 2008 4:47 am
by skid542
Mike,
You have a PM regarding the S/S lines. I am in and waiting on a PayPal address to send the money to.
Thank you.
Todd, if you wanted just the rears then either Mike can split them up or I can split them out when they get here. I could use them on my OBW but if you want them for your Leggy then I have no problems not hanging onto them. I really only need the front for my SS.
Posted: Mon Oct 20, 2008 6:31 am
by skid542
Mike, you have money waiting for you
.
Posted: Tue Oct 21, 2008 3:27 am
by mike270
Brake lines are gone!
Got a few people in line for the intake and "i" badge currently...
Posted: Wed Oct 22, 2008 3:02 am
by mike270
The wheels, badge and intake are now pending!
Everything else listed is still up for grabs.
Posted: Wed Oct 22, 2008 4:45 pm
by wtdash
Did someone else get the Cobb? I never got a reply.
Posted: Fri Oct 24, 2008 1:34 am
by mike270
Sorry, yes the intake was sold to another member on another forum.
Posted: Sun Oct 26, 2008 6:05 am
by skid542
Mike, the lines showed up on Friday and look great - just as described. I'm looking forward to getting them installed tomorrow
.
Thank you for the solid communication and fast shipping.
Take care.
Posted: Sun Oct 26, 2008 5:47 pm
by Buffman
mike got any rear right ABS sensors (1990-1999)?
Posted: Mon Oct 27, 2008 12:54 am
by mike270
Unfortunately I don't have any of those.
Posted: Sun Nov 09, 2008 5:47 pm
by mike270
Sunday bump
Posted: Sun Nov 09, 2008 10:43 pm
by kimokalihi
You've got pm.
Posted: Mon Nov 10, 2008 3:08 am
by mike270
Gasket and flange are gone.
Posted: Thu Nov 13, 2008 3:46 am
by mike270
Suspension and mud flaps are gone.
Posted: Sat Nov 15, 2008 2:59 am
by worunner
Calipers?
Posted: Sat Nov 15, 2008 8:55 pm
by mike270
The calipers are still available if you were interested in them.
Posted: Sat Nov 15, 2008 10:46 pm
by worunner
PM'd
Posted: Sat May 02, 2009 3:45 am
by mike270
Bump.
Posted: Sun Nov 08, 2009 10:44 pm
by mike270
Rotors and brake master are still available!
Re: FS: Random Parts - H6 Rotors, Brake Master Cylinder + mo
Posted: Fri Nov 11, 2011 9:53 pm
by mike270
One final bump to see if someone wants any of this stuff. If not, they will be trashed soon...
