legacycentral bbs

Posted: **Sun Feb 04, 2001 3:49 am**

I had a dyno run on Saturday morning and was very happy with my mods....
last dyno run I was running virtually standard, stock everything except for
apexi pod filter and modified rear muffler ( for more sound than anything ),
boost was 7psi, I got 95.2 kw at the front wheels. Now I was running 3"
downpipe, 3" mandrel bent Fujitsubo exhaust to fujitsubo rear muffler, apexi
pod filter and Blitz EBC set at 14psi and I reached 114.8kw @ 5553 rpm and
peak torque was 703Nm @ 3320 rpm .
I am happy cause so far these mods have only set me back a little under $600
NZ dollars.
However power does fall off quite quickly and assuming this may be
attributed to a dying auto trans so I am hanging out for my STI WRX Gear box
and rear diff.

Regards,

Tommy Moffitt
http://bfcentral.virtualave.net

------------------------ ---------------------~-~>
eGroups is now Yahoo! Groups
Click here for more details
http://click.egroups.com/1/11231/0/_/_/_/981276521/
---------------------------------------------------------------------_->

To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com

Posted: **Sun Feb 04, 2001 4:08 pm**

Tommy said:

>pod filter and Blitz EBC set at 14psi and I reached 114.8kw @ 5553 rpm
and
>peak torque was 703Nm @ 3320 rpm .

Nice! But one question. Can you convert those to HP and Ft/Lbs of Torque for
those stateside that don't know?

Jason

_________________________________________________________________
Get your FREE download of MSN Explorer at http://explorer.msn.com

------------------------ ---------------------~-~>
eGroups is now Yahoo! Groups
Click here for more details
http://click.egroups.com/1/11231/0/_/_/_/981320733/
---------------------------------------------------------------------_->

To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com

Posted: **Sun Feb 04, 2001 4:39 pm**

No problems.
114.8KW at the wheels will be approximately 154BHP or horse power at the wheels.
Based upon 35% drive train loss should be 130.3KW at the flywheel or 175
horsepower
and I will work out torque in a minute......
> Tommy said:
>
> >pod filter and Blitz EBC set at 14psi and I reached 114.8kw @ 5553 rpm
> and
> >peak torque was 703Nm @ 3320 rpm .
>
>
> Nice! But one question. Can you convert those to HP and Ft/Lbs of Torque for
> those stateside that don't know?
>
> Jason
>
>
> _________________________________________________________________
> Get your FREE download of MSN Explorer at http://explorer.msn.com
>
>
>
> To unsubscribe from this group, send an email to:
> BC-BFLegacyWorks-unsubscribe@egroups.com
>
>
>
>

------------------------ ---------------------~-~>
eGroups is now Yahoo! Groups
Click here for more details
http://click.egroups.com/1/11231/0/_/_/_/981322494/
---------------------------------------------------------------------_->

To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com

Posted: **Sun Feb 04, 2001 4:48 pm**

KW*1.341 = hp

>From: "jason grahn" <jgrahn555@hotmail.com>
>Reply-To: BC-BFLegacyWorks@yahoogroups.com
>To: BC-BFLegacyWorks@yahoogroups.com
>Subject: Re: [BC-BFLegacyWorks] Dyno run
>Date: Sun, 04 Feb 2001 135:30 -0800
>
>Tommy said:
>
> >pod filter and Blitz EBC set at 14psi and I reached 114.8kw @ 5553 rpm
>and
> >peak torque was 703Nm @ 3320 rpm .
>
>
>Nice! But one question. Can you convert those to HP and Ft/Lbs of Torque
>for
>those stateside that don't know?
>
>Jason
>
>
>_________________________________________________________________
>Get your FREE download of MSN Explorer at http://explorer.msn.com
>

_________________________________________________________________________
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.

------------------------ ---------------------~-~>
eGroups is now Yahoo! Groups
Click here for more details
http://click.egroups.com/1/11231/0/_/_/_/981322948/
---------------------------------------------------------------------_->

To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com

Posted: **Mon Feb 05, 2001 3:58 am**

--- In BC-BFLegacyWorks@y..., "Tommy Moffitt" <tmoff@i...> wrote:

> peak torque was 703Nm @ 3320 rpm .

Hmmm, are we using different Nm -units (European vs Australian),
cause my car showed 354Nm @ 3850rpm... and 154kW @ 5650 rpm at the
wheels... IIRC the BMW M5 (just as an example) produces 400HP and
500Nm torque.

* Miki *

------------------------ ---------------------~-~>
eGroups is now Yahoo! Groups
Click here for more details
http://click.egroups.com/1/11231/0/_/_/_/981363398/
---------------------------------------------------------------------_->

To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com

Posted: **Mon Feb 05, 2001 4:08 am**

--- In BC-BFLegacyWorks@y..., "Mark Ward" <mark_ward99@h...> wrote:
> KW*1.341 = hp

Shit, I've always used 1.36 when converting kW to HP... now my car
only has 258HP....

* Miki *

------------------------ ---------------------~-~>
eGroups is now Yahoo! Groups
Click here for more details
http://click.egroups.com/1/11231/0/_/_/_/981363627/
---------------------------------------------------------------------_->

To unsubscribe from this group, send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com