legacycentral bbs

Lost my second powersteering cap for the legacy yesterday. It popped off for the 100th time but this time must have fallen onto the street. Called around the local auto stores with no luck. Anyone know where to quickly source these? Or if there is a trick to getting them not to pop off.

http://www.ebay.com/itm/150981494207?it ... 60&vxp=mtr
ordered

Sweet. Now i just need a timing belt cover

Still need a rod and belt covers. Anyone got some?

Someperson wrote:Mass? 01832? Can you ship freight?

Which part?

If its the trans i expect shipping to be over $150 just FYI

I have a spare driveshaft but the joint is ripped. Shipping to main will be well over $150

eggc wrote:I can't recall, is there a way to tell?

It looks like a mirror image of an ej20g harness if that helps

and metal maf

PM'ed

777 ill contact you if I cant find anything. Thanks for the offer.

Also a non dry rotted engine side of a wiring harness

Someperson wrote:And the friggin cylinder walls aren't round...... Wtf was that shop thinking????

huh?

No, they just said 0.020 inches over. Ill look for that birth sheet. Thanks.

I also need a complete time belt cover set

After over heating the exeedy organic clutch I ended up just getting an ACT 6 PAD spung clutch and using it with a exeedy pressure plate. Worked great.

Parts are coming in. Not too happy with my machine shop because they bored the block without having the piston. Not sure how they did the piston to cylinder wall measurements that way. Called Wiseco and they said it should be 0.003 inches for a daily driver. How did you guys grind your piston ring g...

I need one good EJ22T rod. I am sure someone has one laying around.

devilzdriver wrote:how bad would shipping be to hawaii?

Which part?

Ones out a a 1991 turbo legacy the others out of a 1992 turbo legacy. Those are MLSDs and not VLSDs right?

1991 Turbo legacy 3.90 Trans- $400 (with axles) - 130K+, no grinding. http://i1272.photobucket.com/albums/y399/LucyFords/IMAG1257.jpg (2x) 3.90 Rear Diff Mechanical LSD- $250 each (with axles) http://i1272.photobucket.com/albums/y399/LucyFords/IMAG1259.jpg http://i1272.photobucket.com/albums/y399/Lu...

Just realized that there is are two inspection covers on the tank (drivers and pass side). There is another pick up on the drives side and fuel level sensor (so there are two) but i believe the pick up runs on vacuum (not sure). I will look into it some more. But this allowed me to better place my s...

Yeah just got off the phone with Subaru. I guess they only offer them in 0.025 and 0.050 over which isnt what i want. And they are ~$85 a piston without rings/etc.

Yeah those are forged. Looking for cheaper stocker type ones.

Soo these kits dont include pistons. Any suggestions where to get stock oversized pistons?

Yeah I had the tubes hooked up wrong. Had the bottom one and the side one backwards if i remember correctly. Runs great now.

Boost selinode was hooked up wrong...

HI, 90% sure the fuel cut was moved up by the Revtronix chip....I want to say 19psi, but searching on here should tell you. I didn't see it in a quick search of my old Revtronix emails. You do not need an FCD. If you're on the Revtronix (and NOT the Rob tuned EJ20G ECU) your boost should be set by ...

Guys, I just finished installing a TD05 in and took her out for the first run. Pulls hard up to ~5000RPM and then just falls flat on her face. My setup has the JECS MAF, STI 550 injectors, a revtronix stage 2 chip, BUT a stock pump. I am thinking the pump is maxed out. I have a walbro 255 laying aro...