legacycentral bbs

Buying a PP6 and needing the bridging plug so I can keep it on the stock ecu til I get tuned. Anyone have one? https://encrypted-tbn3.gstatic.com/images?q=tbn:ANd9GcSXjp849OdnQYJWPn0RnV710RL8DwHRZjJvo5g_NFzLmUktUHerVg Even if someone would let me borrow it for about a month, I would be forever grate...

Doing a rebuild on a 99 EJ222 out of an OBS, and it turns out that the rings for that engine are harvested from unicorn horns (expensive/hard to find)

So, I need a set of pistons, preferably from a 97-98. Need them shipped to 97526, quick status.

Bump. I specifically need a 90-91 tophat (or pair)

Doing the STi springs on my OBS, and needing a set of rear tophats. I have one good one from a 91 Legacy, so I may only need one, but I'll buy a nicer newer set if anyone has any for sale. PM price shipped to 97526

BTW a new set shipped is around $60. Just throwing that out there.

Not that it's cool or advisable, but you can just put a blanket on the roof and ratchet strap them down. Works in a pinch. It's easy with the Subi frameless doors

http://seattle.craigslist.org/sno/spo/2777456091.html Make sure it has the Q38 clips

http://seattle.craigslist.org/sno/pts/2776472477.html Will need to buy the Q38s, still a screamin deal since a set of Powderhounds costs almost $100 new

You guys get all the cool stuff over there.

How readily available are the pre facelift lights and corners? I'd like a set when the car is less ugly and more worthy of these. They look amazing.

You need about $400 minimum to get the boxer rumble. It has nothing to do with the turbo vs NA unless you care about rumble rumblerumBLERUMBLE RUMBLE WHOOOOOOSH. The rumble is caused by using an unequal length header, minimal muffler interference, and a resonator of some sort. You can do any sort o...

You need about $400 minimum to get the boxer rumble. It has nothing to do with the turbo vs NA unless you care about rumble rumblerumBLERUMBLE RUMBLE WHOOOOOOSH. The rumble is caused by using an unequal length header, minimal muffler interference, and a resonator of some sort. You can do any sort of...

Been good ever since. Taped up the wiring leading to the connector since the insulation looked questionable.

I have yet to acquire the funds to make it happen, but I'm doing a full exhaust to the tune of $400 and change pending on welding costs. Assuming I do the welding myself, I'll be under $400. http://www.semotors.com/tsudo-97-05-subaru-impreza-2-5rs-ej-header-w-downpipe/ Ignore the DP part, it's a cat...

Not that I'm a fan of ABS, but I would like to fix it in my car nonetheless. I could definitely use a new driver rear sensor. If you can find one, I'd also like the driver headlight and corner marker, and a tan passenger sun visor if you have one. Thanks.

Any chance it's ABS and you have a rear sensor in good shape?

If so, there may be other parts I need as well.

In clear memory mode (when you connect both pairs of connectors), the ECU basically does the same thing as it does in D-check mode, except that it clears old stored codes if it doesn't detect any new ones. Your ECU still detects a problem with the knock sensor circuit. Is it possible that the conne...

In clear memory mode (when you connect both pairs of connectors), the ECU basically does the same thing as it does in D-check mode, except that it clears old stored codes if it doesn't detect any new ones. Your ECU still detects a problem with the knock sensor circuit. Is it possible that the conne...

I just finished my engine rebuild and mangled up my crank sensor. Got a known used good one put in, along with a new knock sensor and got the engine running. The plug on the knock was really hard to get in and I ended up not realizing it wasn't totally seated. Upon starting the engine I got a CEL an...

There's a couple down here if you're willing to travel a bit. You can PM me for the info if you'd like.

Since it's not really a structural part of the engine, you can more than likely get away with a 2 part metal "weld" like JB or similar to get it back together. Take your time, clean the area really well, and give it plenty of time to cure.

Soak it in purple power for a little while and blast it with a pressure washer. It takes a VERY long time with the pressure washer before the water running out of the carpet starts to turn clear again but that's when the carpet should be clean. Without the pressure washer I don't see you getting th...

swap in a rs, wrx or sti carpet. I was looking at some WRX carpets on NASIOC and noticed that they looked pretty similar. But then again, close only counts in horseshoes and hand grenades. I think I'll pull the carpet out since I already have the seats out, and try the purple power trick. Didn't ev...

kimokalihi wrote:Meh, not looking to spend that kind of money on them and there were several titles I don't care about or already own. lol plus that auction is over already.

Hey, I figured you'd be on here! It was $50 when I posted it, $68 with 12 seconds to go...

http://www.ebay.com/itm/Nintendo-64-Games-System-/260895345139?pt=Video_Games_Games&hash=item3cbe9309f3#ht_500wt_1202 2 copies of OOT 2 copies of Mario Kart SSB Majora's Mask Mario 64 Looks like 2 Mario Partys 007 diddy kong racing I'd buy it if I had the money. I might if it doesn't jump in the...

One of the POs of my Legacy Wagon had small children, dogs, and was a chain smoker. They also went to the beach and into the mud a lot. At least that's what my interior tells me. I have the seats out of the car and am working on cleaning the carpets, with minimal success. Given how many hours I alre...

Just as the title says. I bought the pair of parking brake cables not knowing if I needed one or both and only used the driver's side. Cable moves freely and clamps are in great shape. $25 shipped. Will also throw in a bunch of parking brake hardware that I thought I might need. Also have the passen...