Get that ass down!

Anything and Everything about the Body, from paint to undercoating and interior, including in-car entertainment (ICE).

Moderators: Helpinators, Moderators

Post Reply
scottzg
Knowledgeable
Knowledgeable
Posts: 2278
Joined: Tue Jan 28, 2003 8:19 am
Location: Saint Joe, CA - Redlands, CA

Get that ass down!

Post by scottzg »

I have a Legacy L (read: no adjustable seats) is there a way i can bring the sitting height down? Bein the monster that i am, i'd really like to get my head away from my visor.

I was contemplating different brackets or just cutting down the foam and reattaching the covering, but i didnt want to get too hasty without guidance. I'd really like to keep my stock seats too, they're comfy and in good condition.

thanks!
[url=http://www.thawa.net/gallery/albums/album108/DSCF0330.jpg]90 legacy of awesomeness[/url]
Yukonart
Cradle Robber
Cradle Robber
Posts: 2655
Joined: Wed Aug 13, 2003 10:45 am
Location: Bothell, WA
Contact:

Post by Yukonart »

Sparco race seats with brackets from Speedware. . . . at least a 2" drop in seating position. :D
JasonGrahn
Knowledgeable
Knowledgeable
Posts: 1333
Joined: Tue Oct 15, 2002 4:55 pm
Location: Seattle, WA
Contact:

Post by JasonGrahn »

chop and drill the factory brackets.
-Jason Grahn
LaureltheQueen
Spelling Nazi
Spelling Nazi
Posts: 4644
Joined: Fri Aug 29, 2003 7:14 am
Location: Lynnwood, WA
Contact:

Post by LaureltheQueen »

or....wrx seats. :)
scottzg
Knowledgeable
Knowledgeable
Posts: 2278
Joined: Tue Jan 28, 2003 8:19 am
Location: Saint Joe, CA - Redlands, CA

Post by scottzg »

wrx seats raise the seat height. Sparcos would look silly in my basically stock legacy, plus they're more money than i really want to spend.

what is involved in chopping and drilling the factory brackets?
[url=http://www.thawa.net/gallery/albums/album108/DSCF0330.jpg]90 legacy of awesomeness[/url]
Yukonart
Cradle Robber
Cradle Robber
Posts: 2655
Joined: Wed Aug 13, 2003 10:45 am
Location: Bothell, WA
Contact:

Post by Yukonart »

Hmmm. . .indeed. . . this will have to be done to Laurel's WRX seats that are going in.

Autocross means helmet must be worn, and Laurel's not exactly short. :?
JasonGrahn
Knowledgeable
Knowledgeable
Posts: 1333
Joined: Tue Oct 15, 2002 4:55 pm
Location: Seattle, WA
Contact:

Post by JasonGrahn »

scottzg wrote:what is involved in chopping and drilling the factory brackets?
Well, you're going to have to figure out where in the rail a new hole needs to be to mount it into the floor. then drill that hole. This will leave you some excess going lower down toward the bottom of your car, you may need to chop that excess to make the fit correct.
-Jason Grahn
ciper
Knowledgeable
Knowledgeable
Posts: 4388
Joined: Tue Oct 15, 2002 8:16 pm
Location: SFCA

Post by ciper »

I have some spair seats with height adjustment if you like. You could transfer the rails and plastic to your current seat.
scottzg
Knowledgeable
Knowledgeable
Posts: 2278
Joined: Tue Jan 28, 2003 8:19 am
Location: Saint Joe, CA - Redlands, CA

Post by scottzg »

i thought the "max low" position on the adjustables was about the same as the normal setting on the fixed position seats. If not, how much lower do they go? And if this is not the case, how much do ya want for the rails?
[url=http://www.thawa.net/gallery/albums/album108/DSCF0330.jpg]90 legacy of awesomeness[/url]
Yukonart
Cradle Robber
Cradle Robber
Posts: 2655
Joined: Wed Aug 13, 2003 10:45 am
Location: Bothell, WA
Contact:

Post by Yukonart »

Oh DUH. Since the WRX driver's side seat has height adjustment, I would think that the position it's in relative to the passenger seat could be lower OR higher. . . so it might at least be able to go down a good inch for helmet clearance. . .

. . . anyone have 2002+ WRX seats in their Legacy who can confirm this? :o
Brat4by4
Stratified
Posts: 1608
Joined: Thu Jan 30, 2003 6:52 am
Location: NE Ohio

Post by Brat4by4 »

I haven't seen stock Legacy seats in a Legacy, but the WRX seats just seem thicker and have much more bolstering than the stock seats. They sit kinda high but not too bad. Yet, I pulled behind a C5 Corvette and it felt like I was sitting in a minivan, though :D . You never hear about people trying to lower those things.

And with the adjustment you can put the seat so high that someone 5'-0" would hit their head on the liner.
1993 WMP BC6 5MT EJ22T 9psi 3.9:1 213k 205/55R16

62.6 m/s @ 0.66 bar. Gotta love boost. :)
Post Reply