The goodies are gonna start rollin' in!! Build time!

Heads, valves, pistons, rods, crankshaft, etc...

Moderators: Helpinators, Moderators

Post Reply
dropdfocus
Fourth Gear
Posts: 1937
Joined: Sun Sep 07, 2003 5:57 am
Location: Williamsport, PA
Contact:
Contact dropdfocus

The goodies are gonna start rollin' in!! Build time!

Post by dropdfocus »

Ok, so I've had to wait until now to get some free cash from working my extra job wiring the local dealership's 6 locations with all new Cat6 wiring so their network is up to date. Of course it's now getting down to the very low 30's at night and highs are in the upper 50's. Oh well...

At least after being VERY patient, I've managed to pick up a brand new TurboXS DTEC fuel controller w/ GameBoy ($380 retail) and TurboXS Fuel Cut Defender ($130 retail) for the total sum of $265!! Gotta love eBay and hella good deals on NASIOC!!!!! Unfortunately, the NASIOC member tanked his motor and needed to sell off his extras to afford another short block or a full rebuild. As for the eBay auction, there were only 2 bids... Go figure.

I'm also now in the process of picking up an STi fuel pump from a local buddy, purchasing STi 550cc injectors (only 7k miles) from a NASIOC member, and the extreme possibility of a TD05H-16g (big 16) from another NASIOC member. Grand total.... $370! :shock: Yup, you read that corretly. :twisted:

So it looks like I REALLY need to get my buddy off his ass to come down to my place and help me cut up the WRX U/P & D/P to make the turbo clear the 2.5 N/A intake manifold. That's pretty much all I really need to get it going (besides stupid misc. exhaust gaskets & missing hoses).

Of course, I still have an EXTREMELY weak link in my build. The 4EAT tranny. So some time in January, I'm hoping to pick up a WRX 5MT and matching rear diff. So by then I'll have my 3.90 LSD for sale. I'll likely sell the tranny to Scott (Tleg-93) for cheap since he's a die-hard user of the automatics. :roll:
Last edited by dropdfocus on Sat Nov 03, 2007 7:42 pm, edited 1 time in total.
Jason
'92 LSS "Trixie" - TD04, '06 WRX TMIC, Invidia D/P & TXS U/P, 3" APEX'i CBE, custom intake, TXS MBC & BPV
Perrin LCP, WRX & H6 brakes, S/S lines, Cusco H-brace & RSTB, AGX's, Progress springs, SimplySubie fender braces
Top
555BCTurbo
Knowledgeable
Knowledgeable
Posts: 3335
Joined: Wed Feb 16, 2005 9:40 pm
Location: Oregon

Post by 555BCTurbo »

WRX Trannies are not 4.11...except the 4EATs

5MTs are 3.90 Front and 3.54 rear
Nick

1987 Audi 4000CS quattro...soon to be 20VT
1994 Dodge Ram 2500 4x4 CTD, #11 plate, 30 psi, Scotty II intake, 4" exhaust
Top
dropdfocus
Fourth Gear
Posts: 1937
Joined: Sun Sep 07, 2003 5:57 am
Location: Williamsport, PA
Contact:
Contact dropdfocus

Post by dropdfocus »

That's right... DUH! I totally forgot about them working with the stock rear diff IF you swap over the center diff gearing to the stock Legacy setup. My bad...
Jason
'92 LSS "Trixie" - TD04, '06 WRX TMIC, Invidia D/P & TXS U/P, 3" APEX'i CBE, custom intake, TXS MBC & BPV
Perrin LCP, WRX & H6 brakes, S/S lines, Cusco H-brace & RSTB, AGX's, Progress springs, SimplySubie fender braces
Top
Steeper
First Gear
Posts: 67
Joined: Wed Jul 04, 2007 7:42 am
Location: Kelowna, BC

Post by Steeper »

you just have to get 1:1 transfer gears, I think they run about 300$ I traded some stuff for mine. But if you get a wrx tranny with a diff, you might as well just use that. I didnt get one, and I have a R180 sti rear diff lying around (3.9) so its a better option for me than finding a wrx diff.
93 impreza wagon
95 v2 STI RA drivetrain
FMIC
002.5 RS bumper and 95 wrx hood
SS 3in TB
Top
dropdfocus
Fourth Gear
Posts: 1937
Joined: Sun Sep 07, 2003 5:57 am
Location: Williamsport, PA
Contact:
Contact dropdfocus

Post by dropdfocus »

Well, I'd like to keep the 3.90 LSD if possible. So I might just try that out then (transfer gears). I have a stock SS 5MT sitting next to my garage (legacy92ej2t's old tranny he tanked 2nd gear in) that I could pull parts from if they'd work. I've researched a LOT on the motor build at this point, but I've been lacking in the transmission research... :(
Jason
'92 LSS "Trixie" - TD04, '06 WRX TMIC, Invidia D/P & TXS U/P, 3" APEX'i CBE, custom intake, TXS MBC & BPV
Perrin LCP, WRX & H6 brakes, S/S lines, Cusco H-brace & RSTB, AGX's, Progress springs, SimplySubie fender braces
Top
Steeper
First Gear
Posts: 67
Joined: Wed Jul 04, 2007 7:42 am
Location: Kelowna, BC

Post by Steeper »

I am not sure on the SS tranny, but I know an impreza tranny you can just swap the whole tail section with the center diff adn the gears. I thought about that but decided I wanted to buy new transfer gears so I could keep the wrx center diff and tail section. personal preference...
93 impreza wagon
95 v2 STI RA drivetrain
FMIC
002.5 RS bumper and 95 wrx hood
SS 3in TB
Top
555BCTurbo
Knowledgeable
Knowledgeable
Posts: 3335
Joined: Wed Feb 16, 2005 9:40 pm
Location: Oregon

Post by 555BCTurbo »

Steeper wrote:I am not sure on the SS tranny, but I know an impreza tranny you can just swap the whole tail section with the center diff adn the gears. .
They are the same
Nick

1987 Audi 4000CS quattro...soon to be 20VT
1994 Dodge Ram 2500 4x4 CTD, #11 plate, 30 psi, Scotty II intake, 4" exhaust
Top
Tleg93
Fifth Gear
Posts: 2281
Joined: Sun Jun 22, 2003 2:52 am
Location: Williamsport, PA

Re: The goodies are gonna start rollin' in!! Build time!

Post by Tleg93 »

dropdfocus wrote: I'll likely sell the tranny to Scott (Tleg-93) for cheap since he's a die-hard user of the automatics. :roll:
Hardy Har har...

I'm a fan of circumstance at this juncture. If I could have me a manual I'd surely have it but it doesn't seem to be in the cards.
--Scott--

1991 - Rio Red SS
Top
dropdfocus
Fourth Gear
Posts: 1937
Joined: Sun Sep 07, 2003 5:57 am
Location: Williamsport, PA
Contact:
Contact dropdfocus

Post by dropdfocus »

Glad you took it all in fun Scott. :)
Jason
'92 LSS "Trixie" - TD04, '06 WRX TMIC, Invidia D/P & TXS U/P, 3" APEX'i CBE, custom intake, TXS MBC & BPV
Perrin LCP, WRX & H6 brakes, S/S lines, Cusco H-brace & RSTB, AGX's, Progress springs, SimplySubie fender braces
Top
Tleg93
Fifth Gear
Posts: 2281
Joined: Sun Jun 22, 2003 2:52 am
Location: Williamsport, PA

Post by Tleg93 »

Oh yeah, no problem. I can take a joke....


I know where you live and I'll be in the shadows waiting. Muahaha.
--Scott--

1991 - Rio Red SS
Top
dropdfocus
Fourth Gear
Posts: 1937
Joined: Sun Sep 07, 2003 5:57 am
Location: Williamsport, PA
Contact:
Contact dropdfocus

Post by dropdfocus »

Tleg93 wrote:I know where you live and I'll be in the shadows waiting. Muahaha.
I'm sorry, could you please turn that up? I'm hard of seeing... (j/k)

Well, I got the TurboXS DTEC F/C today and I'll be paying for the TD05H-16g tomorrow. I should have the STi injectors paid for this week too. Can't wait! :twisted:
Jason
'92 LSS "Trixie" - TD04, '06 WRX TMIC, Invidia D/P & TXS U/P, 3" APEX'i CBE, custom intake, TXS MBC & BPV
Perrin LCP, WRX & H6 brakes, S/S lines, Cusco H-brace & RSTB, AGX's, Progress springs, SimplySubie fender braces
Top
Tleg93
Fifth Gear
Posts: 2281
Joined: Sun Jun 22, 2003 2:52 am
Location: Williamsport, PA

Post by Tleg93 »

I said, good luck on your build.
--Scott--

1991 - Rio Red SS
Top
dropdfocus
Fourth Gear
Posts: 1937
Joined: Sun Sep 07, 2003 5:57 am
Location: Williamsport, PA
Contact:
Contact dropdfocus

Post by dropdfocus »

Uh huh, suuuuuuuure ya did Scott. :lol:

I've already been asked if I'm trying to build some kind of STi killer... Ummm, no.

I just want something that rivaled what Matt (legacy92ej22t) use to have driving past my house each day making me more & more jealous each time he went by.
His was a solid well tuned car that didn't look like anything special but sure as hell took off once your foot started french-kissing the accelerator pedal. :twisted: That's all I'm looking for really.
Jason
'92 LSS "Trixie" - TD04, '06 WRX TMIC, Invidia D/P & TXS U/P, 3" APEX'i CBE, custom intake, TXS MBC & BPV
Perrin LCP, WRX & H6 brakes, S/S lines, Cusco H-brace & RSTB, AGX's, Progress springs, SimplySubie fender braces
Top
Tleg93
Fifth Gear
Posts: 2281
Joined: Sun Jun 22, 2003 2:52 am
Location: Williamsport, PA

Post by Tleg93 »

Once you get there and I get my boost controller, FCD, exhaust some other odds and ends we'll have to put it to the test. :twisted:
--Scott--

1991 - Rio Red SS
Top
dropdfocus
Fourth Gear
Posts: 1937
Joined: Sun Sep 07, 2003 5:57 am
Location: Williamsport, PA
Contact:
Contact dropdfocus

Post by dropdfocus »

Homie, stop playin'. You gonna get a large helpin' of whoop-ass..









Assuming I get the freakin' car finished. :mrgreen:
Jason
'92 LSS "Trixie" - TD04, '06 WRX TMIC, Invidia D/P & TXS U/P, 3" APEX'i CBE, custom intake, TXS MBC & BPV
Perrin LCP, WRX & H6 brakes, S/S lines, Cusco H-brace & RSTB, AGX's, Progress springs, SimplySubie fender braces
Top
dropdfocus
Fourth Gear
Posts: 1937
Joined: Sun Sep 07, 2003 5:57 am
Location: Williamsport, PA
Contact:
Contact dropdfocus

UPDATE!!

Post by dropdfocus »

Well, I'm still picking up parts for my car. Here's what I've wrangled up so far...

TD05-16g turbo (needs a fresh rebuild)
front mount intercooler
EJ25D DOHC heads
EJ20G intake manifold (powder coated wrinkle red)
Walbro 255 fuel pump
550cc injectors
TurboXS Dtec fuel management
TurboXS manual boost controller
LSD from a '91 SS
Progress 1.75" drop springs

Future purchases:
Group N mounts
WRX manual tranny
aftermarket up pipe & down pipe
custom down pipe back exhaust
stock STi struts & springs
aftermarket swaybars & endlinks
brake upgrade (calipers & rotors)
Jason
'92 LSS "Trixie" - TD04, '06 WRX TMIC, Invidia D/P & TXS U/P, 3" APEX'i CBE, custom intake, TXS MBC & BPV
Perrin LCP, WRX & H6 brakes, S/S lines, Cusco H-brace & RSTB, AGX's, Progress springs, SimplySubie fender braces
Top
Post Reply

Return to “Engine”