91/94 turbo Legacy parts, almost anything you need

Jutboy · Post by **Jutboy** » Mon Dec 03, 2007 11:25 pm

I need a blower motor and a hood scoop (black) for my 91 SS.

Can you help PLEASE!!!! Thanks a lot = Justin

the_watts10 · Post by **the_watts10** » Fri Dec 14, 2007 11:35 pm

what color is the car if purple could ibuy the hood and fenders hood only turbo car!!!

SubaruNation · Post by **SubaruNation** » Sat Dec 15, 2007 9:28 pm

the_watts10 wrote:what color is the car if purple could ibuy the hood and fenders hood only turbo car!!!

hmmmmmm...........
wasn't there a thread describing this sort of recurring problem?

the_watts10 · Post by **the_watts10** » Wed Dec 19, 2007 5:35 am

do you have a purple drivers side fender and turbo hood?

lunes · Post by **lunes** » Thu Dec 20, 2007 3:45 am

I have a line on a place to get new OEM style fenders for legacies, fresh off the presses... and they aren't that bad... my friends company gets them at cost for like 90 bucks... I think msrp is like 140 or something...

handson · Post by **handson** » Sun Dec 30, 2007 5:15 am

I need the chrome trim around the passenger rear quarter window for a 90-91 sedan. Also need the top rear window trim and "legacy" badge from below the rear quarter window.

Shipped to 52722.

Thanks!

jimforsyth · Post by **jimforsyth** » Tue Jan 08, 2008 3:35 am

I'm looking for a black outside front drivers door handle shipped to Canada. Available?

Thanks,
Jim Forsyth

subaru legacy turbo · Post by **subaru legacy turbo** » Sat Jan 26, 2008 3:54 am

Any auto trans parts?
Looking for the trans,(93),, rear clutch/differential pack. The inner basket in particular,, I have a pic if you need a reference

Regards
Ian

subaru.legacy.turbo@gmail.com

Blackbart · Post by **Blackbart** » Mon Jan 28, 2008 6:10 am

Woops, looks like I missed the last few posts here.

handson: Pretty sure I have those pieces, I know for sure I have the "legacy" badge

jimforsyth: I have no black door handles, right now all I have is white.

subaru legacy turbo: PM coming

IronMonkeyL255 · Post by **IronMonkeyL255** » Fri Feb 01, 2008 5:45 am

You have a stock BPV?

Blackbart · Post by **Blackbart** » Fri Feb 01, 2008 5:58 am

Yes, and you got PM

abracc · Post by **abracc** » Fri Feb 01, 2008 2:27 pm

I'm sure it's been asked over the past 6 pages, but you don't have a rear power antenna for a wagon, do you? Thanks!!

Blackbart · Post by **Blackbart** » Fri Feb 01, 2008 7:26 pm

Sorry, no antennas. Good ones are real hard to find

abracc · Post by **abracc** » Fri Feb 01, 2008 8:22 pm

I know...I just got accused of wasting people's time asking around for them...

def09 · Post by **def09** » Sat Feb 02, 2008 3:21 pm

Looking for the combination switch assy from 1992 Touring wagon. I screwed the clock spring stuff up installing a momo steering wheel. It would be ideal to try to replace it as an assy. Maybe a steering column cover from same.

Blackbart · Post by **Blackbart** » Sat Feb 02, 2008 4:48 pm

I can send you the combination switch assy on Monday, not sure about the cover, is yours black?

Crashsector · Post by **Crashsector** » Sat Feb 02, 2008 9:24 pm

I just need one ECU connector for any Legacy... I need to salvage the pins to add turbo sensors to my N/A computer. Doesn't matter which plug... just as long as it has at least 5 of the "small" pins in it.

Think you can help?

--Andy

Blackbart · Post by **Blackbart** » Sun Feb 03, 2008 12:25 am

You need the pins out of the ECU itself, not just the male ends from the harness, correct? If this is the case there my be someone out there who has a fryed ECU they can cut up. I will put you in contact with someone I just sold an ecu to, maybe he no longer needs the old one. I will also look through my box-o-harness-tidbits, maybe I can match up something for you.

mike270 · Post by **mike270** » Sun Feb 03, 2008 8:23 pm

I might be in need of a stock T-Leg BPV unless I can figure a work around. Is that something you have?

the_watts10 · Post by **the_watts10** » Tue Feb 05, 2008 4:53 am

1992-1994 purple(brandywine) hood and drivers fender

Legacy Rally Guy · Post by **Legacy Rally Guy** » Wed Feb 06, 2008 5:32 am

I was wondering about the right rear ABS sensor and some sheet metal.

I'd pay for the full pair of front fenders but all I need is from just above the molding down.... my front fneders bottoms are just a little rusty and I figured I'll seam them to my fenders, just behind the molding... A little plug welding, primer and paint and I'm good!

ABS sensors are a bit of a pain, but a sawzall would definitely save me on shipping.. ^^ Unless the fenders like perfect!

Let me know what it'd be for em thanks!
shipping to 63532

lunes · Post by **lunes** » Wed Feb 06, 2008 12:16 pm

man, you need to just order a fender from a company who sells them... I just bought one through a friend who has a body shop in canada, and the fenders for our legacies are not that expensive...

www.crosscanadaparts.com is where my fender is coming from, just for reference.

abracc · Post by **abracc** » Wed Feb 06, 2008 2:19 pm

Do you have the foglight cover thing that goes in place of the fog light in a '93 Turbo Wagon? Driver's side? Thanks!!

Blackbart · Post by **Blackbart** » Wed Feb 06, 2008 3:59 pm

All out of BPV's

No fenders but have a few hoods. Nothing in purple, the closed I have is a turbo 92/94 winestone, faded pretty bad.

I may have the good section of fender from the molding down, I will have to take a look.
I have some ABS sensors, I will look to see which ones I have when I get to the shop today.

I just looked at the site for the new fenders, someone should buy a ton of the 90-91 and put them in a safe place for the future!!!!

I have the foglight blank, PM coming on that.

abracc · Post by **abracc** » Wed Feb 06, 2008 4:31 pm

Got the PM on the foglight...wondered if you had a cargo cover in black back.....also...you don't have the cd player for the legacy do you?

legacycentral bbs

A forum for 89-94 BC-BF(BJ) Legacy Owners and Fans

91/94 turbo Legacy parts, almost anything you need

fenders and hood

Re: fenders and hood