CAI

Snorkus, filters, throttle bodies and intake manifolds.

Moderators: Helpinators, Moderators

Post Reply
94SS_Canada
Third Gear
Posts: 851
Joined: Mon May 12, 2008 4:19 am

CAI

Post by 94SS_Canada »

ya ya, i know, But i need All the room in the world for my FMIC.

Is there any intake that we can use for out T-legs that can simply be bought?

Im running diffrent heads than stock so ther is a few less air lines than stock but what out there is a direct fit/ close fit?
Top
know1
Second Gear
Posts: 520
Joined: Thu Jan 18, 2007 9:28 am
Location: Vancouver, Canada

Post by know1 »

I am pretty sure anything off the shelf would be meant to go under your intake manifold. You said you are running different heads so I presume you are running a different intake manifold. If this is so and you have enough room to run a pipe under your manifold then you should be able to buy any wrx turbo inlet/intake pipe.
1994 Crimson Pearl SS [ td04, 06 fxt tmic,3" catless dp -> apex GT spec exhaust, EDM Tails ]
Top
RJ93SS
Third Gear
Posts: 853
Joined: Mon Jan 14, 2008 7:55 am
Location: Vancouver, Canada

Post by RJ93SS »

subarugenuineparts.com
93SS 04 wrx brakes/slotted w/ hawks--TD05 -- 06 I/C -- 20mm n/a fsb -- Stage 2 -- 550's -- Perrin DIV DP -- 2-3/4 Tit Exhaust -- K&N -- C/C -- A/C Delete -- Grounded -- GT Leather Interior -- WRX/STI Strut Setup -- 17" 225's -- 2 Kids Seats ;)
Top
94SS_Canada
Third Gear
Posts: 851
Joined: Mon May 12, 2008 4:19 am

Post by 94SS_Canada »

Yes the heads and specifically maifold i am running allows more clearance for an intake but no enough to go underneath, i check out geniune parts, thanks
Top
94SS_Canada
Third Gear
Posts: 851
Joined: Mon May 12, 2008 4:19 am

Post by 94SS_Canada »

RJ93SS wrote:subarugenuineparts.com
Just went there, couldnt find anything?
Top
RJ93SS
Third Gear
Posts: 853
Joined: Mon Jan 14, 2008 7:55 am
Location: Vancouver, Canada

Post by RJ93SS »

it's called the spt turbo legacy cold air intake, it wont be a bolt up but it wouldn't take much to make it work for ya!
93SS 04 wrx brakes/slotted w/ hawks--TD05 -- 06 I/C -- 20mm n/a fsb -- Stage 2 -- 550's -- Perrin DIV DP -- 2-3/4 Tit Exhaust -- K&N -- C/C -- A/C Delete -- Grounded -- GT Leather Interior -- WRX/STI Strut Setup -- 17" 225's -- 2 Kids Seats ;)
Top
know1
Second Gear
Posts: 520
Joined: Thu Jan 18, 2007 9:28 am
Location: Vancouver, Canada

Post by know1 »

would this be the spt intake for the new legacy turbos?

I was looking at it, it doesn't look to tough to fit.
1994 Crimson Pearl SS [ td04, 06 fxt tmic,3" catless dp -> apex GT spec exhaust, EDM Tails ]
Top
94SS_Canada
Third Gear
Posts: 851
Joined: Mon May 12, 2008 4:19 am

Post by 94SS_Canada »

what about FMIC piping?

is it a short ram?
FastRust
Top
RJ93SS
Third Gear
Posts: 853
Joined: Mon Jan 14, 2008 7:55 am
Location: Vancouver, Canada

Post by RJ93SS »

i think it's a bit of a short ram, basically it's just a starter for designing your own intake, what i will be doing after my td04 goes in is designing an intake from a cold air source with minimal elbows and long big straight pieces of pipe, if you dont know how to weld you could use silicone 90's or desighn something from pipe and tape the gaps and take it to somebody else to weld.

when i finish mine...one day.... i'll post up my desighn and results for the site
93SS 04 wrx brakes/slotted w/ hawks--TD05 -- 06 I/C -- 20mm n/a fsb -- Stage 2 -- 550's -- Perrin DIV DP -- 2-3/4 Tit Exhaust -- K&N -- C/C -- A/C Delete -- Grounded -- GT Leather Interior -- WRX/STI Strut Setup -- 17" 225's -- 2 Kids Seats ;)
Top
94SS_Canada
Third Gear
Posts: 851
Joined: Mon May 12, 2008 4:19 am

Post by 94SS_Canada »

okay, i forget where all the air returns go now though

Does somebody have a diagram for all those intake air hoses?
FastRust
Top
94SS_Canada
Third Gear
Posts: 851
Joined: Mon May 12, 2008 4:19 am

Post by 94SS_Canada »

http://forums.nasioc.com/forums/showthr ... ?t=1492915

Is this what you guys were talking about?
Top
Post Reply

Return to “Intake”