I apparently knocked the intake off the engine, but since it was
under that plastic cover thingy I didn't notice it until a little
wisp of smoke came out of there while trying to start... yikes. Now
my question is this... should I reset the ECU again, since
I 'touched' the throttle? Why does it make such a point to say don't
touch the throttle?
--- In BC-BFLegacyWorks@y..., "DNA_Man" <dna_man@y...> wrote:
> I just replaced my filter with a K&N, and I cleaned the battery and
> cables at the same time. I left the battery disconnected for 60
> minutes to reset the ECU, then I tried to start the car and 'not
> touch the throttle until the car warms up', just like the
> instructions say. Now the car won't start at all. It turns over
fine
> with the starter and then it sputters out and dies. Pushing on the
> gas makes no difference. Before doing this there was no problem, I
> just wanted to use the K&N filter. I need to go get some lunch...
I'm
> starving... and my car won't start... help! How can I tell if the
MAF
> is freakin out?
------------------------ ---------------------~-->
PC to PC calling with 3-way conferencing. Only
$11.95/yr at CrystalVoice! Free trial. Click Here!
http://us.click.yahoo.com/4SQRwC/RYfDAA ... /XoTolB/TM
---------------------------------------------------------------------~->
To unsubscribe from this group, please send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com
No start after ECU reset (I'm a dumbass)
Moderators: Helpinators, Moderators
-
milehial2000
No start after ECU reset (I'm a dumbass)
I wouldn't worry about touching the throttle I deal with these on
almost a daily basis and I don't think that such a reset even exists
except for clearing defaults and trouble codes. Where did the smoke
come from? That may be something to worry about if something shorted
and burned.
AL(CO)
--- In BC-BFLegacyWorks@y..., "DNA_Man" <dna_man@y...> wrote:
> I apparently knocked the intake off the engine, but since it was
> under that plastic cover thingy I didn't notice it until a little
> wisp of smoke came out of there while trying to start... yikes. Now
> my question is this... should I reset the ECU again, since
> I 'touched' the throttle? Why does it make such a point to say don't
> touch the throttle?
>
>
> --- In BC-BFLegacyWorks@y..., "DNA_Man" <dna_man@y...> wrote:
> > I just replaced my filter with a K&N, and I cleaned the battery
and
> > cables at the same time. I left the battery disconnected for 60
> > minutes to reset the ECU, then I tried to start the car and 'not
> > touch the throttle until the car warms up', just like the
> > instructions say. Now the car won't start at all. It turns over
> fine
> > with the starter and then it sputters out and dies. Pushing on the
> > gas makes no difference. Before doing this there was no problem, I
> > just wanted to use the K&N filter. I need to go get some lunch...
> I'm
> > starving... and my car won't start... help! How can I tell if the
> MAF
> > is freakin out?
------------------------ ---------------------~-->
FREE COLLEGE MONEY
CLICK HERE to search
600,000 scholarships!
http://us.click.yahoo.com/G_L2TD/4m7CAA ... /XoTolB/TM
---------------------------------------------------------------------~->
To unsubscribe from this group, please send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com
almost a daily basis and I don't think that such a reset even exists
except for clearing defaults and trouble codes. Where did the smoke
come from? That may be something to worry about if something shorted
and burned.
AL(CO)
--- In BC-BFLegacyWorks@y..., "DNA_Man" <dna_man@y...> wrote:
> I apparently knocked the intake off the engine, but since it was
> under that plastic cover thingy I didn't notice it until a little
> wisp of smoke came out of there while trying to start... yikes. Now
> my question is this... should I reset the ECU again, since
> I 'touched' the throttle? Why does it make such a point to say don't
> touch the throttle?
>
>
> --- In BC-BFLegacyWorks@y..., "DNA_Man" <dna_man@y...> wrote:
> > I just replaced my filter with a K&N, and I cleaned the battery
and
> > cables at the same time. I left the battery disconnected for 60
> > minutes to reset the ECU, then I tried to start the car and 'not
> > touch the throttle until the car warms up', just like the
> > instructions say. Now the car won't start at all. It turns over
> fine
> > with the starter and then it sputters out and dies. Pushing on the
> > gas makes no difference. Before doing this there was no problem, I
> > just wanted to use the K&N filter. I need to go get some lunch...
> I'm
> > starving... and my car won't start... help! How can I tell if the
> MAF
> > is freakin out?
------------------------ ---------------------~-->
FREE COLLEGE MONEY
CLICK HERE to search
600,000 scholarships!
http://us.click.yahoo.com/G_L2TD/4m7CAA ... /XoTolB/TM
---------------------------------------------------------------------~->
To unsubscribe from this group, please send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com
-
DNA_Man
No start after ECU reset (I'm a dumbass)
Where the intake goes into the engine, a little smoke came out after
the car died. I thought it might have been electrical like you say,
but there's no electrical stuff in there. My engine has recently been
disassembled to replace the valve cover gaskets, and the mechanic did
not tighten the hose clamp on the intake so I knocked it off when I
changed the filter. Why they took it off I'm not sure, but in the
course of tracking down this problem I noticed quite a few hoses
pulled from their brackets and the plug wires were not in their
holders either. It looks like they went after the valve covers from
the top...
BTW, there is a noticeable power difference with the K&N filter... I
would definately recommend it. I can't believe I've been
RallyCrossing without it! Next month... ICE Rally Cross
(That's in Georgetown btw... www.coloradorally.org for more info)
--- In BC-BFLegacyWorks@y..., "milehial2000" <acroxford@h...> wrote:
> I wouldn't worry about touching the throttle I deal with these on
> almost a daily basis and I don't think that such a reset even
exists
> except for clearing defaults and trouble codes. Where did the smoke
> come from? That may be something to worry about if something
shorted
> and burned.
> AL(CO)
>
>
>
>
> --- In BC-BFLegacyWorks@y..., "DNA_Man" <dna_man@y...> wrote:
> > I apparently knocked the intake off the engine, but since it was
> > under that plastic cover thingy I didn't notice it until a little
> > wisp of smoke came out of there while trying to start... yikes.
Now
> > my question is this... should I reset the ECU again, since
> > I 'touched' the throttle? Why does it make such a point to say
don't
> > touch the throttle?
> >
> >
> > --- In BC-BFLegacyWorks@y..., "DNA_Man" <dna_man@y...> wrote:
> > > I just replaced my filter with a K&N, and I cleaned the battery
> and
> > > cables at the same time. I left the battery disconnected for 60
> > > minutes to reset the ECU, then I tried to start the car
and 'not
> > > touch the throttle until the car warms up', just like the
> > > instructions say. Now the car won't start at all. It turns over
> > fine
> > > with the starter and then it sputters out and dies. Pushing on
the
> > > gas makes no difference. Before doing this there was no
problem, I
> > > just wanted to use the K&N filter. I need to go get some
lunch...
> > I'm
> > > starving... and my car won't start... help! How can I tell if
the
> > MAF
> > > is freakin out?
------------------------ ---------------------~-->
Send FREE Holiday eCards from Yahoo! Greetings.
http://us.click.yahoo.com/IgTaHA/ZQdDAA ... /XoTolB/TM
---------------------------------------------------------------------~->
To unsubscribe from this group, please send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com
the car died. I thought it might have been electrical like you say,
but there's no electrical stuff in there. My engine has recently been
disassembled to replace the valve cover gaskets, and the mechanic did
not tighten the hose clamp on the intake so I knocked it off when I
changed the filter. Why they took it off I'm not sure, but in the
course of tracking down this problem I noticed quite a few hoses
pulled from their brackets and the plug wires were not in their
holders either. It looks like they went after the valve covers from
the top...
BTW, there is a noticeable power difference with the K&N filter... I
would definately recommend it. I can't believe I've been
RallyCrossing without it! Next month... ICE Rally Cross
(That's in Georgetown btw... www.coloradorally.org for more info)
--- In BC-BFLegacyWorks@y..., "milehial2000" <acroxford@h...> wrote:
> I wouldn't worry about touching the throttle I deal with these on
> almost a daily basis and I don't think that such a reset even
exists
> except for clearing defaults and trouble codes. Where did the smoke
> come from? That may be something to worry about if something
shorted
> and burned.
> AL(CO)
>
>
>
>
> --- In BC-BFLegacyWorks@y..., "DNA_Man" <dna_man@y...> wrote:
> > I apparently knocked the intake off the engine, but since it was
> > under that plastic cover thingy I didn't notice it until a little
> > wisp of smoke came out of there while trying to start... yikes.
Now
> > my question is this... should I reset the ECU again, since
> > I 'touched' the throttle? Why does it make such a point to say
don't
> > touch the throttle?
> >
> >
> > --- In BC-BFLegacyWorks@y..., "DNA_Man" <dna_man@y...> wrote:
> > > I just replaced my filter with a K&N, and I cleaned the battery
> and
> > > cables at the same time. I left the battery disconnected for 60
> > > minutes to reset the ECU, then I tried to start the car
and 'not
> > > touch the throttle until the car warms up', just like the
> > > instructions say. Now the car won't start at all. It turns over
> > fine
> > > with the starter and then it sputters out and dies. Pushing on
the
> > > gas makes no difference. Before doing this there was no
problem, I
> > > just wanted to use the K&N filter. I need to go get some
lunch...
> > I'm
> > > starving... and my car won't start... help! How can I tell if
the
> > MAF
> > > is freakin out?
------------------------ ---------------------~-->
Send FREE Holiday eCards from Yahoo! Greetings.
http://us.click.yahoo.com/IgTaHA/ZQdDAA ... /XoTolB/TM
---------------------------------------------------------------------~->
To unsubscribe from this group, please send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com
-
milehial2000
No start after ECU reset (I'm a dumbass)
Your ok then if just came out of the intake. I have a K&N mounted
under my front fender. I took a two channel temp recorder and checked
the under hood vs the under fender temps in moderate traffic in the
summer. There was 70-80 degrees difference and I could tell the change
with the cold air intake. I might check Georgetown out I was up there
and we were racing snowmobiles on the lake several years ago.
AL(CO)
--- In BC-BFLegacyWorks@y..., "DNA_Man" <dna_man@y...> wrote:
> Where the intake goes into the engine, a little smoke came out after
> the car died. I thought it might have been electrical like you say,
> but there's no electrical stuff in there. My engine has recently
been
> disassembled to replace the valve cover gaskets, and the mechanic
did
> not tighten the hose clamp on the intake so I knocked it off when I
> changed the filter. Why they took it off I'm not sure, but in the
> course of tracking down this problem I noticed quite a few hoses
> pulled from their brackets and the plug wires were not in their
> holders either. It looks like they went after the valve covers from
> the top...
>
> BTW, there is a noticeable power difference with the K&N filter... I
> would definately recommend it. I can't believe I've been
> RallyCrossing without it! Next month... ICE Rally Cross
>
> (That's in Georgetown btw... www.coloradorally.org for more info)
>
> --- In BC-BFLegacyWorks@y..., "milehial2000" <acroxford@h...> wrote:
> > I wouldn't worry about touching the throttle I deal with these on
> > almost a daily basis and I don't think that such a reset even
> exists
> > except for clearing defaults and trouble codes. Where did the
smoke
> > come from? That may be something to worry about if something
> shorted
> > and burned.
> > AL(CO)
> >
> >
> >
> >
> > --- In BC-BFLegacyWorks@y..., "DNA_Man" <dna_man@y...> wrote:
> > > I apparently knocked the intake off the engine, but since it was
> > > under that plastic cover thingy I didn't notice it until a
little
> > > wisp of smoke came out of there while trying to start... yikes.
> Now
> > > my question is this... should I reset the ECU again, since
> > > I 'touched' the throttle? Why does it make such a point to say
> don't
> > > touch the throttle?
> > >
> > >
> > > --- In BC-BFLegacyWorks@y..., "DNA_Man" <dna_man@y...> wrote:
> > > > I just replaced my filter with a K&N, and I cleaned the
battery
> > and
> > > > cables at the same time. I left the battery disconnected for
60
> > > > minutes to reset the ECU, then I tried to start the car
> and 'not
> > > > touch the throttle until the car warms up', just like the
> > > > instructions say. Now the car won't start at all. It turns
over
> > > fine
> > > > with the starter and then it sputters out and dies. Pushing on
> the
> > > > gas makes no difference. Before doing this there was no
> problem, I
> > > > just wanted to use the K&N filter. I need to go get some
> lunch...
> > > I'm
> > > > starving... and my car won't start... help! How can I tell if
> the
> > > MAF
> > > > is freakin out?
------------------------ ---------------------~-->
Send FREE Holiday eCards from Yahoo! Greetings.
http://us.click.yahoo.com/IgTaHA/ZQdDAA ... /XoTolB/TM
---------------------------------------------------------------------~->
To unsubscribe from this group, please send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com
under my front fender. I took a two channel temp recorder and checked
the under hood vs the under fender temps in moderate traffic in the
summer. There was 70-80 degrees difference and I could tell the change
with the cold air intake. I might check Georgetown out I was up there
and we were racing snowmobiles on the lake several years ago.
AL(CO)
--- In BC-BFLegacyWorks@y..., "DNA_Man" <dna_man@y...> wrote:
> Where the intake goes into the engine, a little smoke came out after
> the car died. I thought it might have been electrical like you say,
> but there's no electrical stuff in there. My engine has recently
been
> disassembled to replace the valve cover gaskets, and the mechanic
did
> not tighten the hose clamp on the intake so I knocked it off when I
> changed the filter. Why they took it off I'm not sure, but in the
> course of tracking down this problem I noticed quite a few hoses
> pulled from their brackets and the plug wires were not in their
> holders either. It looks like they went after the valve covers from
> the top...
>
> BTW, there is a noticeable power difference with the K&N filter... I
> would definately recommend it. I can't believe I've been
> RallyCrossing without it! Next month... ICE Rally Cross
>
> (That's in Georgetown btw... www.coloradorally.org for more info)
>
> --- In BC-BFLegacyWorks@y..., "milehial2000" <acroxford@h...> wrote:
> > I wouldn't worry about touching the throttle I deal with these on
> > almost a daily basis and I don't think that such a reset even
> exists
> > except for clearing defaults and trouble codes. Where did the
smoke
> > come from? That may be something to worry about if something
> shorted
> > and burned.
> > AL(CO)
> >
> >
> >
> >
> > --- In BC-BFLegacyWorks@y..., "DNA_Man" <dna_man@y...> wrote:
> > > I apparently knocked the intake off the engine, but since it was
> > > under that plastic cover thingy I didn't notice it until a
little
> > > wisp of smoke came out of there while trying to start... yikes.
> Now
> > > my question is this... should I reset the ECU again, since
> > > I 'touched' the throttle? Why does it make such a point to say
> don't
> > > touch the throttle?
> > >
> > >
> > > --- In BC-BFLegacyWorks@y..., "DNA_Man" <dna_man@y...> wrote:
> > > > I just replaced my filter with a K&N, and I cleaned the
battery
> > and
> > > > cables at the same time. I left the battery disconnected for
60
> > > > minutes to reset the ECU, then I tried to start the car
> and 'not
> > > > touch the throttle until the car warms up', just like the
> > > > instructions say. Now the car won't start at all. It turns
over
> > > fine
> > > > with the starter and then it sputters out and dies. Pushing on
> the
> > > > gas makes no difference. Before doing this there was no
> problem, I
> > > > just wanted to use the K&N filter. I need to go get some
> lunch...
> > > I'm
> > > > starving... and my car won't start... help! How can I tell if
> the
> > > MAF
> > > > is freakin out?
------------------------ ---------------------~-->
Send FREE Holiday eCards from Yahoo! Greetings.
http://us.click.yahoo.com/IgTaHA/ZQdDAA ... /XoTolB/TM
---------------------------------------------------------------------~->
To unsubscribe from this group, please send an email to:
BC-BFLegacyWorks-unsubscribe@egroups.com