Collecting parts for my 06 intercooler install.
I went to Horsepower Freaks in Portland. Their a high presure sales outfit that doesnt seem to worried about your business unless your dropping big bucks, Been there three times. Been un-impressed each time. Anyways. got a Silicone intercooler hose kit for a06-07 WRX. They didnt have them in stock so I got them shipped. a few days later (at least thier service was prompt) Got the Kit via FedX. Open it up... no hose clamps. Went back to HPF and was promptly blown off and told to goto Baxters auto suppy. Well. Baxters doesnt sell that type of hose clamp, doesnt deal with the company that made my hoses (Samco sport for the inquiring mind) and cant order the clamps in the size I need. Went to the manufacturers websight, there is a "clip kit" made. but only available through retailers.
At this point I really dont want to waste my time or my money at HPF. Anybody know a retailer that deals with SAMCO sport. or for that matter can order a generic set of clips that will fit.
On another subject. 06-07 intercooler. to the right of the throttle body there is a place for a daimond shaped piece of metal to bolt on that (I think) Plumbs to the blow off valve... My intercooler doesnt have the piece of metal. Anyone know what it is called so I can order a new one?
Thanks in advance!
Looking For Hoseclamps for my Intercooler piping.
Moderators: Helpinators, Moderators
Looking For Hoseclamps for my Intercooler piping.
Dave
_________________
1993 Legacy Sport Sedan 4EAT "Angel" *sold*
_________________
1993 Legacy Sport Sedan 4EAT "Angel" *sold*
The adapter plate you need is this one: you will also need to figure out how to adapt the BPV hose onto it.
Ebay Link
Or, custom make your own plate, it should not be too hard.
Ebay Link
Or, custom make your own plate, it should not be too hard.
1991 SS build thread: http://bbs.legacycentral.org/viewtopic.php?t=40430
-
- Fifth Gear
- Posts: 8360
- Joined: Mon Nov 06, 2006 3:41 am
- Location: Tenino, WA
I too bought the same samco y pipe kit and 06 intercooler. I need the hose clamps as well. I'm about to buy an EJ25D intake manifold that should hopefully clear the BPV so I won't need this adapter but if not I'll need to buy this one.
Where do you get the clamps?
Where do you get the clamps?
98 Metro Hatch Daily Driver :)
91 SS EJ20G Engine/Tranny/Diff Swap Build Thread Here
"Your testes are close to your bottom but you still play with them all the time." Jeremy Clarkson
91 SS EJ20G Engine/Tranny/Diff Swap Build Thread Here
"Your testes are close to your bottom but you still play with them all the time." Jeremy Clarkson
From looking around at others setups, I was under the impression the correct clamps to get for the silicon hoses are t-clamps. The worm clamps will dig into the tubing, I thought.
I just ordered up my y-tube and t-clamps from http://www.maperformance.com (NASIOC vendor)... we'll see how it all works out when they arrive later this week. Then time for the install and detailed writeup.
I just ordered up my y-tube and t-clamps from http://www.maperformance.com (NASIOC vendor)... we'll see how it all works out when they arrive later this week. Then time for the install and detailed writeup.
'11 WRX Limited
'94 SS | 3" TBE, 07 TMIC, TD05H-16G, Revtronix Stage 2, Walbro -- Sold
'94 TW | R.I.P.
-
- Fifth Gear
- Posts: 3043
- Joined: Tue Jan 25, 2005 9:14 pm
- Location: Twin Cities, MN