WTB: 06/07 WRX Intercooler Y pipe

SubaruNation · Post by **SubaruNation** » Mon Jan 05, 2009 5:29 pm

whats up guys,

i think the subject should describe it.

i need one, so if you wanna sell let me know. Preferably one that has not been destroyed, if possible.

let me know,

thanks alot!

wtdash · Post by **wtdash** » Mon Jan 05, 2009 7:23 pm

One of these, correct?

I should still have mine....I'll let ya know by tomorrow.

Td

SubaruNation · Post by **SubaruNation** » Mon Jan 05, 2009 7:40 pm

maybe its just me but that looks different.

it should look like this:

thanks tho

ScottyS · Post by **ScottyS** » Mon Jan 05, 2009 7:41 pm

That one looks to have pre-06 geometery, Td.

Nation, if you are looking for something to work with an 06 IC on a 22T, you will need a silicone y-pipe + 2" exhaust pipe and good clamps.

The stock one, once modified, just didn't last because of the plastic design.

SubaruNation · Post by **SubaruNation** » Mon Jan 05, 2009 7:43 pm

ya i can do it with either one.

preferably the plastic kind b/c they are cheaper and i have a vf11.

another bump if you want to sell yours!

SubaruNation · Post by **SubaruNation** » Fri Jan 09, 2009 5:46 am

le bump.

anyone....?

SubaruNation · Post by **SubaruNation** » Fri Jan 09, 2009 4:19 pm

does anyone know where i can buy an all silicon one?

any recommendations?

thanks

Will something like this work?

le click

le clickity 2

SubaruNation · Post by **SubaruNation** » Fri Jan 09, 2009 6:34 pm

http://cgi.ebay.com/ebaymotors/_Car-Tru ... 240%3A1318

ScottyS · Post by **ScottyS** » Fri Jan 09, 2009 9:57 pm

Do a search. There were a bunch of posts on that eBay STi one a while back.

Just kidding. The one that will be the easiest to deal with is probably the Prodrive silicone one for the 06 WRX/FXT. The turbo outlet side gets cut and rotated 180* to point straight down and spliced in with a short piece of 2" pipe. You then use a slightly-modified STi OEM 90* off the turbo outlet and some 2" pipe in between it and the Y.

Don't forget the ol' dryer hose fallback.

SubaruNation · Post by **SubaruNation** » Sat Jan 10, 2009 2:43 am

ScottyS wrote:Do a search. There were a bunch of posts on that eBay STi one a while back.

Just kidding. The one that will be the easiest to deal with is probably the Prodrive silicone one for the 06 WRX/FXT. The turbo outlet side gets cut and rotated 180* to point straight down and spliced in with a short piece of 2" pipe. You then use a slightly-modified STi OEM 90* off the turbo outlet and some 2" pipe in between it and the Y.

thank you

here

ScottyS wrote: Don't forget the ol' dryer hose fallback.

joking or what..?

wtdash · Post by **wtdash** » Mon Jan 12, 2009 3:13 am

Sorry for the delay..finally got back in the garage to work on my next project and found the Ypipe.

I think this is from an '06 WRX...but not sure. I do know it doesn't fit on an old '02 WRX TMIC I still need to get rid of.

As you likely know this doesn't mate up to a TD04 (let alone a VF11) as is....you'll need to get creative.

Let me know if you're still interested. This is an actual pic of what I have. The insulation is a PITA to remove so I didn't:

SubaruNation · Post by **SubaruNation** » Mon Jan 12, 2009 7:23 pm

i think im going to get a silicone samco hose and make that work.

i am making due with the crappy plastic one now, but if i just replace it w/ the same thing i feel i'll end up in the exact same place here in 3 months when the plastic goes bad again.

thanks though

Saskatoon Subaru · Post by **Saskatoon Subaru** » Mon Mar 02, 2009 2:55 am

I have an 06 intercooler if your still looking

SubaruNation · Post by **SubaruNation** » Mon Mar 02, 2009 5:49 pm

ha.

thanks for the offer, i have mine all set up now w/ silicone and its awesome.

legacycentral bbs

A forum for 89-94 BC-BF(BJ) Legacy Owners and Fans

WTB: 06/07 WRX Intercooler Y pipe

WTB: 06/07 WRX Intercooler Y pipe

Ypipe