auxiliary oil cooler

Heads, valves, pistons, rods, crankshaft, etc...

Moderators: Helpinators, Moderators

Post Reply
93Leg-c
Fourth Gear
Posts: 1886
Joined: Mon Oct 27, 2003 7:17 am
Location: Oahu, Hawaii, USA

auxiliary oil cooler

Post by 93Leg-c »

I just wanted some input on this auxiliary oil cooler.

http://cgi.ebay.com/ebaymotors/ws/eBayI ... 72049&rd=1

Are the statements in the ad accurate or is it just a sales pitch?
'94 TW
Top
THAWA
Knowledgeable
Knowledgeable
Posts: 6829
Joined: Thu Aug 21, 2003 7:44 pm
Location: Sacramento, CA
Contact:
Contact THAWA

Post by THAWA »

I think the bit about the heat exchanger not being useful after a while is true. As far as the temp drop, it depends on the setup. I'd say its possible if your oil is mad hot before the cooler.
Rio Red 90 Legacy LS AWD 174k
Liquid Silver 92 SVX LS-L 88k
[url=http://folding.amdmbpond.com/FoldingForOurFuture.html]Do you fold?[/url]

I'm on First and First. How can the same street intersect with itself? I must be at the nexus of the universe.
Top
93Leg-c
Fourth Gear
Posts: 1886
Joined: Mon Oct 27, 2003 7:17 am
Location: Oahu, Hawaii, USA

Post by 93Leg-c »

So, if I ever want to build a turbo motor with a td05 16g I should consider using this auxiliary oil cooler or something similar to it?
'94 TW
Top
THAWA
Knowledgeable
Knowledgeable
Posts: 6829
Joined: Thu Aug 21, 2003 7:44 pm
Location: Sacramento, CA
Contact:
Contact THAWA

Post by THAWA »

I would personally. What you should do though if you're undecided, is get an oil temp gauge. Put it on before you do upgrades and then once you're done, if the oil temp is way more than it was before get an oil cooler. Course if the oil temp is way more than it should be in the first place you should get one now, or better yet, try to find out why its so hot.
Rio Red 90 Legacy LS AWD 174k
Liquid Silver 92 SVX LS-L 88k
[url=http://folding.amdmbpond.com/FoldingForOurFuture.html]Do you fold?[/url]

I'm on First and First. How can the same street intersect with itself? I must be at the nexus of the universe.
Top
93Leg-c
Fourth Gear
Posts: 1886
Joined: Mon Oct 27, 2003 7:17 am
Location: Oahu, Hawaii, USA

Post by 93Leg-c »

Good suggestions. Thanks!

So what's the "ideal" oil temperature? And what's acceptable?
'94 TW
Top
THAWA
Knowledgeable
Knowledgeable
Posts: 6829
Joined: Thu Aug 21, 2003 7:44 pm
Location: Sacramento, CA
Contact:
Contact THAWA

Post by THAWA »

Ya got me :)
Rio Red 90 Legacy LS AWD 174k
Liquid Silver 92 SVX LS-L 88k
[url=http://folding.amdmbpond.com/FoldingForOurFuture.html]Do you fold?[/url]

I'm on First and First. How can the same street intersect with itself? I must be at the nexus of the universe.
Top
vrg3
Vikash
Posts: 12517
Joined: Sun Nov 03, 2002 2:13 am
Location: USA, OH, Cleveland (sometimes visiting DC though)
Contact:
Contact vrg3

Post by vrg3 »

Most oil cooler thermostats are set to a temperature similar to that of an engine coolant thermostat... I don't think it 's a coincidence; doesn't it make sense that they'd engineer motor oils to work best at the optimal engine running temperature?
"Just reading vrg3's convoluted, information-packed posts made me feel better all over again." -- subyluvr2212
Top
evolutionmovement
Knowledgeable
Knowledgeable
Posts: 9809
Joined: Mon Jun 16, 2003 11:20 pm
Location: Beverly, MA

Post by evolutionmovement »

It would also explain Subaru's heat exchanger as it equalizes oil and coolant temp.

Steve
Midnight in a Perfect World on Amazon or order anywhere. The first book in a quartet chronicling the rise of a man from angry criminal to philanthropist. Midnight... is a distopic noirish novel featuring 'Duchess', a modified 1990 Subaru Legacy wagon.
Top
93Leg-c
Fourth Gear
Posts: 1886
Joined: Mon Oct 27, 2003 7:17 am
Location: Oahu, Hawaii, USA

Post by 93Leg-c »

So then, ideal oil temp should be 190 degrees F since our cars use the 190 degree thermostat? The ad mentions 160 degrees as normal working temp. I know the Subaru thermostat for the radiator coolant starts opening at 176 degrees. And Subaru says a 160 degree thermostat is not recommended.
'94 TW
Top
EJ20TMAN
In Neutral
Posts: 48
Joined: Mon Feb 17, 2003 4:20 am
Location: New Zealand
Contact:
Contact EJ20TMAN

Post by EJ20TMAN »

Unless u are pulling 300hp + i wouldnt evn bother.
1990 GT wagon JDM, TD05H, FMIC, Bosch coils 4in twin split dump 3 in rest of system, lowered, manual conversion, 17's, 17psi boost :) , tints, intake res gone and loving it!!!
Top
Matt Monson
quasi-mod-o
quasi-mod-o
Posts: 2574
Joined: Sun Nov 09, 2003 8:24 pm
Location: Ghetto Garage, CO, USA
Contact:
Contact Matt Monson

Post by Matt Monson »

I missed this thread the first time. That cooler is a rip off. You can get an OEM one off of a Forester in a junkyard for much much cheaper. You just need the cooler itself and a water pump with the extra bung. And if you wanted to plumb in a heat exchanger, a B&M one could be had for around $50-75. The whole thing could be done for less than $200 and just as effective as that fancy all american looking one...
1974 Porsche 914 Cam Am Limted Edition AKA the Bumble Bee
1973 Porsche 914 2.0 l -Suby swap pending
1968 Porsche 911t survivor 47k original miles
2000 2.5RS daily driver.
1999 2.5RS w/ 50+ extra whp
Suby Hai!
Top
Kelly
Fourth Gear
Posts: 1286
Joined: Sat Nov 01, 2003 5:35 pm

Post by Kelly »

93Leg-c wrote:So then, ideal oil temp should be 190 degrees F since our cars use the 190 degree thermostat? .
Yup :wink:

210 is gettin hot


Additional benifits to the factory cooler is that it warms your car up faster, it has its own T stat I beleive, and it keeps the oil and coolant close in temputure, reducing the risk of cracking heads. Less hoses to come loose break/leak, dont have to worry about rocks punchin through it, and so on.

Volvo 740 Turbos have a sandwich plate, and setrab oil cooler. I always look for em at the wreckers, and can usually get away with them for about 20 bones. Havnt tried to fit one on a soobie yet, but I bet they'd fit.
Top
93Leg-c
Fourth Gear
Posts: 1886
Joined: Mon Oct 27, 2003 7:17 am
Location: Oahu, Hawaii, USA

Post by 93Leg-c »

Thanks for all the info, guys. It's helping me figure out what I'll need to do.

rallitektech, what's a sandwich plate and a setrab oil cooler?
'94 TW
Top
Kelly
Fourth Gear
Posts: 1286
Joined: Sat Nov 01, 2003 5:35 pm

Post by Kelly »

A sandwich plate goes between the oil filter, and the oil filter housing.
Image

its an easy way to get oil to, and back from a cooler.

Setrab is an OEM manufacturer of coolers. Good Quality. :wink:

HTH
Top
93Leg-c
Fourth Gear
Posts: 1886
Joined: Mon Oct 27, 2003 7:17 am
Location: Oahu, Hawaii, USA

Post by 93Leg-c »

Aah, thanks for explaining!

And here comes another question, What's "HTH"--your initials or . . . .??? (Sorry if it's a silly question)
'94 TW
Top
vrg3
Vikash
Posts: 12517
Joined: Sun Nov 03, 2002 2:13 am
Location: USA, OH, Cleveland (sometimes visiting DC though)
Contact:
Contact vrg3

Post by vrg3 »

Hope that helps. :)
"Just reading vrg3's convoluted, information-packed posts made me feel better all over again." -- subyluvr2212
Top
93Leg-c
Fourth Gear
Posts: 1886
Joined: Mon Oct 27, 2003 7:17 am
Location: Oahu, Hawaii, USA

Post by 93Leg-c »

vrg3 wrote:Hope that helps. :)
Thanks! :)
'94 TW
Top
Post Reply

Return to “Engine”