legacycentral bbs

Got a few pictures of the Outback maplight/sunglass holder and one of the light bar. Pardon the quality, I used my phone.


All the gaps/holes...




And the light bar!! I still need to add the final support so it won't shake but atleast its black now.

I like how it says Outback still haha

That thing's pretty cool. Still leaves the front grille vent open and keeps the headlights
far enough off of the hood to be able to close. Interested in more pics. Got 4 Hella's
my car's been dying for.

Its pretty basic, two flat stock bars coming from the upper radiator holder things and, since I don't have a welder to use, a two foot bar of angle iron bolted to the two flat stock bars and, I still need to add the support bar that will bolt to the fron of the angle iron to the lower bar with the foglights on it. The upper bar has room for 4 rounds lights too.

How's your support bar going to work? Will you have to contour it around the front bumper?

Autocrossed my touring wagon for the first time. Did pretty well for my first time on H rated tires (all the top dawgs had slicks).

Finally got to adding the support to the light bar, its not what I was planning at all. But the bar is done other than paint and I got a can of flat black already. For some reason, the big round lights aren't working but the other set of lights on the bar work fine. I would have pictures but I finished after dark. Oh and I finally finished installing the grey dash yesterday.

James: Haha, nice man!

Danny: Cool dude. Get some pictures up when you can

Stupid Washington rain! Kept me from painting the rest of the light bar. But I did but some bigger wires in for the positive and negative of one switch. And I would have pictures but the camera batteries are dead..

Just layed some JB weld on my old "L" grille. Hopefully it won't break this time and hopefully I'll get it done before spring.

I replaced my moon roof with an intake manifold, should be good for 23hp



...actually deride's former SS remains are on my trailer, and as I clean m garage I needed a way to get the scrap in to the car.

Finally got the light bar pictures uploaded.



And the '91ss interior parts I swapped in.



Also, a little thing mud does that I noticed.

Danny-G wrote:Finally got the light bar pictures uploaded.



And the '91ss interior parts I swapped in.



Also, a little thing mud does that I noticed.

Looks pretty sweet, dude!

Grayguy wrote:

Where there's your problem....you've got an intake manifold in your moon roof....

Legacy777 wrote:

Grayguy wrote:

Where there's your problem....you've got an intake manifold in your moon roof....

wtf?!?!?!

poor moon roof. what did it do to you other than give you a nice view of the moon. lol but now its a forced air intake.

modified roof vent

Custom weight savings

Lol!

4 legged spider attacked the moon roof!

ericem wrote:Pics say it all



swapped out the old motor and tranny, swapped in a older lower mileage working motor and tranny

Now with some new motor mounts that would work great with the duel tranny set up. ha

SWRT wrote:

This gold was the Dupli-color Gold engine enamel stuff. Worked good. Didnt turn out
too bad looks-wise.

Depends what clear coat you use. The color looked a bit different before the coats of clear.

http://www.rs25.com/forums/f105/t136579 ... ldies.html

i just bought those wheels for $200 from my bff. gonna look good on the whip. ps i dig the flaps.

Had some muddy doughnuts at midnight. Now my car is almost all brown.

installed coolant temp sensor in 92L. Reading the OBD I codes...actually kinda fun.

Moonroof short block swap!



Apparently it takes 6-7 wheel barrows of Subaru parts to fill a BC. The garage is a lot cleaner tho. The next cleaning project involves welding some 1" rebar across the front frame rails so I can jamb 3-4 motors in the engine bay, pics to follow haha

Like you said, only if it was a wagon... could fit a lot more shit in it.