legacycentral bbs

I had the task of designing a circuit that: Did not modify the vehicle in any way Produced the lowest resistance to the lights Used the minimum amount of components Lowest cost I have now a tested design that has two function, one being the normal operation of high lamps on when high is selected, lo...

Rear facing is the one near the firewall while front facing is the one that will sit right above the throttle body cover support right?

Non turbo. Heavily modified suspension but basically stock engine. I do have a scooped hood to be installed (using the wrx sized scoop). I currently have a little over 4k saved to do an engine swap. I plan to install a low mileage (under 10k) 2003 wrx engine. Im still contemplating wether I want to ...

I plan to take some more, I think you would be very surprised at the cleanliness of my engine bay. I can work all day on the car and without gloves get no dirt or grease. Its funny, I was helping a freind work on his truck and I "forgot" that you get dirty. When I pulled my hand out I was ...

Well, I know for one thing that THE WHEELS MUST STILL TRAVEL AT NEAR THE SAME SPEED.

For example, putting the fwd fuse in and testing on a two wheel dyno while the rear wheels remain still does damage the center diff (just not very much).

No, 1-2 IS a band! It actually works like this First and third are true gears, clutch based. The second gear is a modifed first while the 4th gear is a modified 3. When in first if you tighten the modifier band it increaes the speed of the output. When shifting to third, the band must be released th...

What color code is that

totech: The rest is pretty wild.

You think thats weird? Check this out http://zerobrid.tripod.co.jp/

Search around for adjusting the band. If the RPM raise when shifting from 1-2 then the band is slipping.

I rather like the solid black trim, I wish I had it. I plan to add the signals on the side like he has. I just wonder how he was able to smog the thing. You can easily tell its not USDM from the image of the back of the car, the plate in the middle of the tail lights is very different.

"1990 1.8i-16V" "Chipped, approx. 130hp" I must be in the damn twilight zone or something. A california 90 Legacy with a 130hp 1.8 liter fuel injected engine with a chip?! This guy is smoking some serious dope. http://www.cardomain.com/member_pages/view_page.pl?page_id=226723&...

Remember, some people dropped out so he still needs 2 or 3 for a bumper and 1 or 2 for the hood!

BTW, when do we get the parts?

That car is only about 30 miles away from me. Maybe I could get some parts?

It is rigged, look at the two 7 with the dot in the miles, and the second and third 7 on the trip. They are identicle (in a pair)

Look at this, ouch! Check out the last image

http://cgi.ebay.com/ebaymotors/ws/eBayI ... 1873160070

NGK Coppers, they are cheap and performance!

While looking at that picture you have to listen to the music from

http://216.130.176.127/Weeee(mov).swf

thanks eastbaysubaru

No such thing. The manual transmission on all cars 90+ are strictly mechanical, except the XT6 which had a lockable center diff.

I have a photo but I dont have a place to host it. The original image is 3040 pixel by 2016 pixel

I love the color! That roof hump is freaking me out though, what versions have that? I dont remember seeing that until later.

Too bad it takes 2+ weeks to get them. He doesnt keep any in stock

I suggest a quick test, switch to another name brand gas and try using the highest octane in that brand available for one full tank (fill up when near empty).

Then when the tank is half empty reset the ECU again and drive around and see if the problem exists.

Bill, since you are replacing your auto what are you doing with the left over electronics? I would be interested to see the shift patterns and such from a later TCU compared to a 90 and 92.

They only cost about 25k

Too bad too, I know someone who is a 4x4 nut who would almost buy them even at that price.

I like the part in the video where the truck floats over the snow then the guy steps in between the tracks and sinks!

So for those of you who used the strut tops, they come with all the hardware that sits between the spring and the body or??? What do you have to reuse?

I assume that these let you use the Large diameter springs right?

I did some more research. In fact this does provide better lighting with a very similar (hard to measure) beam pattern. The difference is that the filament in this bulb is perpendicular to that of the 9004. Just create two notches in the bulbs or snap the tabs off in your existing housing and they w...