legacycentral bbs

Price?

sold?

call or text 585-230-1315

I got a voltex diffuser. Let the hate or the love flow through you. :) http://tapatalk.imageshack.com/v2/14/10/02/aa1bd552e9fda14b3ffaf93702fc2470.jpg http://tapatalk.imageshack.com/v2/14/10/02/b298977124d77739abee5d061c73b365.jpg That's super funny I test fitted my buddies off his sti onto my car ...

I want one , just for winter

Holy crap I want bright ol fogs! http://tapatalk.imageshack.com/v2/14/09/24/a68f742d52b772f4a617fe1564d9e472.jpg http://tapatalk.imageshack.com/v2/14/09/24/07dbfffbdfb2b76963add6c2a23b95bc.jpg http://tapatalk.imageshack.com/v2/14/09/24/4bea90f9277ff03d3965c2dd2a67c75a.jpg http://tapatalk.imageshack....

dillonr92 wrote:Oh for real?
I was just saying if they were 100% clear it would be that much more sharp and crystal light. They are a 100% difference from stock tho. They look good man. Good job. I'm planning on doing the morimoto mini h1's.

The actual projector lens needs to be cleaned just took them apart.

dillonr92 wrote:You shoulda cleared them lenses atleast a circle 2 inches wider than the projector

They're a lot clearer than you think.
I spent time to wet sand , use brush on rubbing compound then buffed them.

Finished them, with one minor setback. PO replaced the driver side headlight with something aftermarket ( I couldn't tell ) and it melted in pretty bad. Next time I'll make sure it says subaru in the lens. Going to the junkyard to get another one and swap lenses. http://img.tapatalk.com/d/14/09/23/a...

Dominator wrote:Right on! Definitely keep us posted. I'm very curious to see how they come out. I've wanted to retro fit a pair for my car too, but the fluted lenses have discouraged me.

I will make a write up when I finish

My Mercedes projectors came on, started to wire them, going to try to put them in tomorrow

dillonr92 wrote:Raquan. Get 185/45/15 tires and you can go that much lower or do 185/40/15 tires

I'm going to raise it, it's not that fun being so low.

dillonr92 wrote:Lowered it another half inch. Still have another quarter inch to go before I'm rubbing boot

This is as far as I can go

Lowered it
Lol

Made a new gauge holder today

Has anyone done a rotated setup with a rob tuned ecu?

I wanted to ask here before emailing rob.
Thanks

Ripped the front end apart for some changes

killajamal wrote:Test fitted my new sideskirts. Hopefully I can come up with an effective way to secure them permanently!


Sent from my XT897 using Tapatalk

I want some! jealous!

starter died at work
15 minute swap!

I redid some old vac lines and solders some wires

Legacy777 wrote:You may want to peel back the wiring loom and tap to see if it's tapped into one of the wires or is tied into the shielding.

looks like it was connected there. Car won't start now haha. Guess I'll solder it back on

I need one haha!

Legacy777 wrote:Is it going into one of the MAF pins and if so, what pin is it going into?

I'm confused I didn't go into a specific pin?

cj91legss wrote:Almost done with my electrical on my 205 22t swap. Car is coming along well. Better than I expected.

Can't wait to drive it.

Oooo write up?
I have a 205 in the garage the needs a rebuild and was thinking of doing that swap

Legacy777 wrote:Does this wiring look like something that has been added? Any chance you could take a picture of it?

Sorry for the delay

macipusy wrote:Might still be able to get a set from the dealership....but for an arm and a leg.

I don't even want to know their price haha