FS: AN fittings for clutch hose

Got something for sale? Need to sell a part? Got some stuff on auction that you want to let us know about?

(Legacy Central BBS is not responsible for any arbitration between its users relative to this forum.
Play nice and deal straight)

Moderators: Helpinators2, Moderators

Forum rules
Please see the NEW Parts Shed Rules before posting: http://www.bbs.legacycentral.org/viewto ... 15&t=55814

Sales of parts and parting cars only. Complete or parted car posts should be made in Car Lot: http://www.bbs.legacycentral.org/viewforum.php?f=32
Post Reply
IronMonkeyL255
Fourth Gear
Posts: 1902
Joined: Sat Aug 09, 2003 5:02 pm
Location: Woodruff, SC

FS: AN fittings for clutch hose

Post by IronMonkeyL255 »

I have in my possession the 2 fittings required for adapting a universal AN-3 hose to a '91 SS clutch master cylinder and slave cylinder.

I bought 2 of the banjo fittings (AN-3 to 10mm), assuming that they didn't change from '91 to '92. I was wrong, and only needed one and had to scramble to order the proper fitting for the slave cylinder (AN-3 to m10x1.0). The correct fitting came in packs of 2, though, so I have an extra one of those as well.

I'll part with them for $15. All you need other than these is an AN-3 hose. I used a 14" hose with a straight swivel and a 90 degree end, though the same ends on a 12" hose would have been sufficient. I put the 90 degree end on the slave cylinder and the straight end on the master cylinder.

Here's a link to the site where I ordered my hose and one of the fittings from.

http://www.pegasusautoracing.com/produc ... ?Product=3


For clarification, these are for use if your slave cylinder has a fitting that looks like this:

Image


I have no real use for these, so I figured I would offer them up for anyone else that may need them.
Disclaimer: If anything I post is inaccurate, please correct me. I do not wish to add to the misinformation floating around on the internet.

That being said, everything I post is accurate to the best of my knowledge.

Rio Red '91 Legacy SS
Top
AWD_addict
Fifth Gear
Posts: 2774
Joined: Sun Nov 23, 2003 12:22 am
Location: Western WA!

Post by AWD_addict »

I'm interested.

So you're using a banjo with banjo bolt and 2 washers on the master end, and a AN-3 to m10x1.0 ( http://www.pegasusautoracing.com/produc ... RecId=4191 ) on the slave end?
90 L+ wgn
Top
IronMonkeyL255
Fourth Gear
Posts: 1902
Joined: Sat Aug 09, 2003 5:02 pm
Location: Woodruff, SC

Post by IronMonkeyL255 »

Not that specific adapter, but that is what I did.

The Earl's version has a slight inversion on the M10x1.0 end that I felt was necessary for proper sealing. The stock fitting had it, so I went through the trouble of getting it.

If you want, I could probably get a pic of my setup. The hoses that Pegasus carries are genuine Goodridge hoses, so they are good quality.
Disclaimer: If anything I post is inaccurate, please correct me. I do not wish to add to the misinformation floating around on the internet.

That being said, everything I post is accurate to the best of my knowledge.

Rio Red '91 Legacy SS
Top
AWD_addict
Fifth Gear
Posts: 2774
Joined: Sun Nov 23, 2003 12:22 am
Location: Western WA!

Post by AWD_addict »

Yeah, please get a pic of it.

The pic of the Earl's version is pretty poor. http://www.bakerprecision.com/adapt10.htm
90 L+ wgn
Top
IronMonkeyL255
Fourth Gear
Posts: 1902
Joined: Sat Aug 09, 2003 5:02 pm
Location: Woodruff, SC

Post by IronMonkeyL255 »

Here's a better pic of just the fitting:

Image

Note how it inverts towards the end in the right hand pic. That seems to be where it seals, and what the Pegasus version seemed to be missing.

My camera sucks, so I couldn't take a pic. The only shot I could get is of the end attached to the master cylinder. The slave cylinder is inconveniently stuffed far under my WRX TMIC.
Disclaimer: If anything I post is inaccurate, please correct me. I do not wish to add to the misinformation floating around on the internet.

That being said, everything I post is accurate to the best of my knowledge.

Rio Red '91 Legacy SS
Top
IronMonkeyL255
Fourth Gear
Posts: 1902
Joined: Sat Aug 09, 2003 5:02 pm
Location: Woodruff, SC

Post by IronMonkeyL255 »

Oh, yeah.

I also have a brand new banjo bolt for this as well. I ordered one for each banjo fitting I thought I needed, then only turned out to need the one.
Disclaimer: If anything I post is inaccurate, please correct me. I do not wish to add to the misinformation floating around on the internet.

That being said, everything I post is accurate to the best of my knowledge.

Rio Red '91 Legacy SS
Top
AWD_addict
Fifth Gear
Posts: 2774
Joined: Sun Nov 23, 2003 12:22 am
Location: Western WA!

Post by AWD_addict »

How much do want for the three parts? (banjo fitting, banjo bolt, and AN-3 to M10x1.0)
90 L+ wgn
Top
IronMonkeyL255
Fourth Gear
Posts: 1902
Joined: Sat Aug 09, 2003 5:02 pm
Location: Woodruff, SC

Post by IronMonkeyL255 »

$15 shipped will do it.

They are small and light, so it shouldn't be much to ship it.

I figure that's a bit less than I paid, but you do still have to order the line. Even with the line, though, it's still pretty cheap.
Disclaimer: If anything I post is inaccurate, please correct me. I do not wish to add to the misinformation floating around on the internet.

That being said, everything I post is accurate to the best of my knowledge.

Rio Red '91 Legacy SS
Top
AWD_addict
Fifth Gear
Posts: 2774
Joined: Sun Nov 23, 2003 12:22 am
Location: Western WA!

Post by AWD_addict »

I'll take em. PM on the way!
90 L+ wgn
Top
Post Reply

Return to “Parts Shed”