legacycentral bbs

Will jumped timing cause a no spark condition? Im starting to lean towards that, because i replaced the cam position sensor and it still shows up on the CEL codes after i cleared them.

Tested and still have no spark. I cleared all the codes, but the cam position sensor code came back on after i installed a new sensor.

Ok, here we go. So this past weekend we had a cold front move in, and about 8 inches of snow, got pretty cold. I went to start the car saturday night, and i heard a single click from under the hood, but the started would not engage. So i tried turning the key a few more times, and just still a singl...

ok, so im moving to colorado and i have to take my 94 legacy turbo along bc i havent had any luck finding a newer LGT yet. sooo for exhaust on my 94 i have a bellmouth dp, going into 3 inch exhaust all the way back. there is a resonator and then la large ebay muffler at the back. the entire system w...

ok well i got the bill today. he replaced the control arm and ball joint and alligned the car all for a grand total of 150 bucks with tax. not too bad. and plus he worked me in right away and got the car done quickly.

ya i hope so too man. What would a rough estimate be for parts and labor to get back on the road? Its already at my local sube shop that has all kinds of parts cars around.

So a few nights ago i was driving to the gym and went to make the right hand turn to the entrance and lost grip (my fault for going too fast for the road conditions) and smacked into a few small xmas trees and ran into and over a tall curb and got high centered. Well i didnt feel like waiting around...

the past two trips i have made with the car(94 SS 4EAT) it has been cold outside, under 25 deg. F. So i go out and start the car up and at idle it comes up to temperature (half way on the gauge) like it should and the heater blows hot air. But as soon as i hit the freeway and increased speed brings ...

Last week i had a horrible screeching grinding noise coming from the back of the car when under braking pressure, so i just assumed my pads were worn. WEll i took the car into the local sube shop, and it turned out that it had the wrong rotors on there, (NA rotors) and that when the pads wore down t...

IM not sure this is in the right section, be here it goes. Last night i was taking off both front calipers to get the rotors turned down and i noticed the driver side had a wheel stud (or lug) that was slightly cross threaded. so i decided to knock it out and go get a new one. So i knocked it out bu...

bringin back up an old thread here, but im also looking at a set of 05 WRX wheels. What do you guys think about a deep gold color on an Agean Blue met car?

noooo not tight as hell. Dont overtorque them.

i measured the fitting on the adapter flange, and its actually 1 1/4 inch o.d. i got a piece of 1 inch to fit over it so im hoping i can clamp the 1 inch over the BPV tight enough to make it work. WEll its 7 pm and im off to start the install. how far ya think i'll get before i make it back around m...

i just dont see how this is going to work. THe adapter flange is much much larger fitting that what the BPV does. it would seem to me that a intermediate hose would be way too small on one end and too big on the BPV side. Also, does everyone elses' 06-07 wrx TMIC have the sloped black pastic top to ...

the adapter plate has a bigger fitting that what the BPV valve does. am i going to have to try and find a reducer for this? also anybody know what size bolts to get to secure the adapter flange to the TMIC??

so i found a set of Legacy MEsh or snowflakes or whatever you want to call them 16X6.5 IIRC. they have 205/55/16. From everything ive searched it seems that this is a hit and miss size tire for different years in regards to rubbing. I have a 94 with stock struts and suspension. Can anyone confirm th...

blackbart, looking for the mechanism ( i think its a pressure sensor) that sits on the inside of the passenger side fender in the engine bay. It has a few vacum lines and one runs to the turbo silencer. This sensor is the one that is directly above the boost control solenoid. Price shipped to 26623....

ok, so i got my silicone intakes order in today and i went out and test fit everything before the instal. TMIC to TB coupler works great 90 elbow from the turbo outlet (1.75 id) fits a little loose over the outlet but i think it will work. ONly question i have is, i got an BOV adapter for the TMIC o...

ironmonkey, what is the 45 bend for? i ordered a 90 silicone bend to fit off the turbo, then should i get the mandrel 45 to hook the 90 up to the y-pipe on the intercooler? any idea how long to make it. using a 06 WRX TMIC.

a BOV will work, but your car wil most likelyl run rich everytime the bov dumps atmospherically.

i found a set of stock 2002 wrx wheels with tires for sale and i've been searching and it seems like this bolt pattern will work. any words of advice before i purchase this set? i.e. what tire sizes to run or stay away from?

Thanks bro. car isnt with me right now as im at school so i cant measure. but i'll get on that as soon as i get back to it. WHat, you want this ol ABM? haha she let me down a few nights ago, got stuck in park while i was out on a date. an hour and a half later me and the chick got the override down ...

SO the elbow i need to get is for sure 1.5 inside diameter? i hate buying something then having to return it. and am i correct in thinking the throttle body to TMIC coupler is 3 inch id?

Exactly, but if the air is recirced back into the intake then the ECU actually doesnt even know it went a different path and should give a steady air/fuel mixture. So, anybody know for sure what style of BOV to use, so that it doesnt hit the cruise and throttle cables? Also, for the stock vf-11 turb...

SO from what i've seen most ppl. on here try and retain their stock BPV when upgragiding to a top mount intercooler. OTher than the extra cost issue, if you have an aftermarket BOV that is properly recirculated are there any more problems associated with using an aftermarket BOV dump. Also, for thos...